Question about Hobart Quantm1-1lb50 Quantum Scale With Printer

Open Question

I need to adjust a feed gear on a hobart quantum scale

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 876 Answers

SOURCE: how do i program prices per lb and oz on quantum scale

You can go to Hobart.com:

http://www.hobartservice.com/main/default.aspx

and create a new user and download a manual.

Posted on Feb 03, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hobart handler 125 wire feed gears broken teeth. Have three teeth broken on plastic gear. Can I get replacement gears?


You are probably going to have to replace the complete assembly, and it is probably going to cost about $150. I would contact Hobart by phone with your serial #, and they should have the correct part# , since there is no parts list in your manual, and none seem to be available on line. BRwelders has part# 210010 listed but may not be correct, since it is for the 120.

http://www.brwelder.com/kit-feed-mot...er-120-210010/

Jun 04, 2017 | Hobart Welding Tools

1 Answer

Hobart scales lines in display


All LCD displays have a connector from the main board, and it may also be ON the main board, and may have a long, special connector that is layers of silicone and conductive material that connects the back of the glass display with the connection points on the PC board.
When one of these points is not connected, you can get a blank line or a dark line on the display. Either way, you have to take the front panel off and try a few things. Sometimes just disconnecting and reconnecting the display connector is all that is needed. In the case of the silicone connector, the screws or clips that hold it together need to be loosened, the connection moved, and then re-tightended.
In the case of an intelligent display, there will be just a few wires, as few as 5 or so. In this case, the fault is in the display itself, and you have to get a new LCD display.

Jun 11, 2014 | Hobart Quantm1-1ss Quantum Self-service...

1 Answer

What is the meaning of "thermal overload" hobart quantum scales


The is something called a duty cycle and if you exceed that rating then you have to wait for it to cool off to use it again.

Oct 14, 2013 | Hobart Kitchen Ranges

1 Answer

Why does scale print extra label?


sounds like it is setup to print a secondary label. go into supervisor mode 10 and check to make sure the secondary label setting is at 0

Aug 22, 2012 | Hobart Quantm1-1ss Quantum Self-service...

1 Answer

How to set up a hobart quantum scale to print EAN13 label


you need to add a ean13 label type to your scale. this is something only a service tech. or hobart rep can do.

Mar 26, 2012 | Office Equipment & Supplies

1 Answer

Trying to weld with Hobart 125 EZ


If you are using flux wire and not shielding gas, your clamp should be positive and the wire should be negative. Heat is provided by the electrical arc that happens between the wire and the material. Your welder by itself does not pre heat the material and with 3/16 material you should not need to preheat anyway.

The electrical arc is kept consistent by adjusting the wire feed rate and the current applied. You will need to experiment with these settings to find what works best with your welder. For this welder and 3/16 material, I would suggest you start at the upper end of the current scale and about a third of the way up on wire speed. The welder might have a chart for these settings in the manual or inside cover.

If the wire feeds too fast, it will push the probe around and you will feel pressure as the wire feeds out. If the speed is too slow you will get large spatters and intermittent arcs. When properly adjusted the arc will sound even and consistent. The arc gap should always be about 1/8 of an inch.

To maintain enough heat for good penatration, do not move the probe too fast, work in a pattern and watch the weld pool (melted metal) and not the arc. Watching the weld pool will clue you in if you are moving too fast or too slow.

I hope this helps.

-Scott

Feb 03, 2009 | Hobart Handler 125 Ez

Not finding what you are looking for?
Hobart Quantm1-1lb50 Quantum Scale With Printer Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Kitchen Ranges Experts

Brad Brown

Level 3 Expert

15557 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14790 Answers

ka4iup
ka4iup

Level 3 Expert

3957 Answers

Are you a Hobart Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...