Question about Pioneer Televison & Video

1 Answer

MY PIONEER AUDIO/VIDEO RECEIVER WON' TURN ON

MY PIONEER REVEIVER WON'T COME ON, THE STAND-BY LIGHT JUST BLINKS, I PULLED THE COVER OFF TO LOOK FOR A RESET BUTTON OR SOMETHING, BUT THERE WAS NONE. I CHECKED BOTH FUSES AND THEY WERE BOTH GOOD. I BELIEVE WE LOST POWER BEFORE WE FOUND THE RECIEVER IN THIS MODE.

Posted by on

  • 1 more comment 
  • primalfearch Jan 02, 2009

    Unplugging

  • primalfearch Jan 02, 2009

    the unit and holding the power button, then plugginit back in didn't do anything, the stand-by light still blinking.

  • primalfearch Jan 03, 2009

    this is a 6 channel receiver, not a 7.1 channel receiver.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,142 Answers

Did you try to do a power cycle ?

Posted on Jan 02, 2009

  • Maanita Chadha
    Maanita Chadha Jan 02, 2009

    Unplug the power cable then push hold the power button for a few seconds and then try connecting the power cable and see what happens.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TV turns red,shuts off, stand-by light blinking 8Times


Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D board.

Feb 27, 2014 | Sony KP-51HW40 51" Rear Projection...

1 Answer

I have a pioneer pro 730hd took the back off and now the red power light just blinks and it wont turn on


If convergence was off it may have railed (shorted convergence chip) and the set is now in shutdown.

Also go over inside in case you moved or pulled a plug loose.

This is not an easy set to replace the chips and only the original remote will adjust convergence.

Mar 17, 2012 | Pioneer PRO-730HD 64" Rear Projection...

1 Answer

Sony blinking codes


If i remember correctly ten blinks means a high voltage error.
The only thing you could try is unplugging the power cord then plug it back in and try turning on the tv. If it still won't turn on try unplugging the power cord for five hours or longer and try again. If it still won't turn on it would be best to find a local repair shop that works on sony tv's and have them repair it for you.

Mar 01, 2012 | Sony Grand WEGA KDP-51WS550 51" Rear...

1 Answer

No picture, no sound. Stand bye 4 red light blinks


Hi,
The Standby/Power light of the TV blinks when there is any internal malfunction in the TV. The self-diagnostic function of the TV will cause the STANDBY light to blink or flash when the television detects an issue. The number of times the STANDBY light flashes corresponds to a specific issue.
Few examples are given below; some of the issues may be resolved without the need for service.
1 blink / 2 blinks / 5 blinks: - This indicates that there may be a power-related problem with your set.
3 blinks: - This indicates that there may be a power-related problem with your set. The set will need to be serviced to allow a technician to determine the specific issue that needs to be repaired. If the power light flashes three times in sequence in a Lamp TV, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue.
4 blinks: - This indicates that there may be a back light or lamp power problem.
6 blinks: - This indicates that there is some kind of audio problem with your set.
7 blinks: - This indicates that there is a temperature problem with your set. Please check to make sure that the air vents on the sides and back of the set are not blocked or clogged and there is adequate ventilation around the television. We recommend that you check and clean the vents periodically to make sure the set receives adequate air flow. If the problem continues, the set will need to be serviced.
8 blinks: - This indicates that there may be a video-related problem with your set. If the flash sequence is not listed above or the light continues to flash, follow the steps below to perform a power reset:
Try the following steps to check if the issue can be resolved.
Turn off the television.
Unplug the television power cord from the electrical outlet.
Let the television remain without power for 60 seconds.
Plug the power cord back into the electrical outlet.

If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
If the issue continues to occur, service may be required.

Thanks for using Fixya.

Jul 17, 2011 | Sony KP-53S70 53" Rear Projection...

1 Answer

I have a sony 65 in. sxrd projection tv that has the red power light blinking and the tv won't come on?


Hi,
The Standby/Power light of the TV blinks when there is any internal malfunction in the TV. The self-diagnostic function of the TV will cause the STANDBY light to blink or flash when the television detects an issue. The number of times the STANDBY light flashes corresponds to a specific issue.
Few examples are given below; some of the issues may be resolved without the need for service.
1 blink / 2 blinks / 5 blinks: - This indicates that there may be a power-related problem with your set.
3 blinks: - This indicates that there may be a power-related problem with your set. The set will need to be serviced to allow a technician to determine the specific issue that needs to be repaired. If the power light flashes three times in sequence in a Lamp TV, the lamp cover is not securely attached. Reattach the lamp cover to resolve this issue.
4 blinks: - This indicates that there may be a back light or lamp power problem.
6 blinks: - This indicates that there is some kind of audio problem with your set.
7 blinks: - This indicates that there is a temperature problem with your set. Please check to make sure that the air vents on the sides and back of the set are not blocked or clogged and there is adequate ventilation around the television. We recommend that you check and clean the vents periodically to make sure the set receives adequate air flow. If the problem continues, the set will need to be serviced.
8 blinks: - This indicates that there may be a video-related problem with your set. If the flash sequence is not listed above or the light continues to flash, follow the steps below to perform a power reset:
Try the following steps to check if the issue can be resolved.
Turn off the television.
Unplug the television power cord from the electrical outlet.
Let the television remain without power for 60 seconds.
Plug the power cord back into the electrical outlet.

If the television is plugged into a power strip or surge protector, remove it from the power strip or surge protector and plug it directly into the wall outlet. If the issue is resolved, the problem is with the power strip or surge protector and not the television.
If the issue continues to occur, service may be required.

Thanks for using Fixya.

Jul 16, 2011 | Sony Televison & Video

1 Answer

Sony kdf e50 a60 when TV is turned on picture goes off almost immedately and red light starts blinking in stand by mode.


Red light blinking is an indication of lamp problem. Check and secure tightly the following:
  1. Outside lamp cover
  2. Lamp door
  3. Lamp
If all of the above does not solve the problem, you need to replace the lamp. Let the lamp to cool for 30 minutes after unplugging. Use XL-2400 replacement lamp.
  1. Remove the outside lamp cover.
  2. Remove the lamp door.
  3. Pullout the lamp
  4. Hook a finger through the loop of the lamp handle and pull the handle upwards. Then pull the lamp straight out.
  5. Mount the new lamp securely.
  6. Reattach the lamp door. Turn the knob back to "CLOSE" and secure the cover.
  7. Put the outside lamp cover back in its place.
or visit http://www.fixya.com/support/t2631342-need_replace_42_in_sony_wega_hdtv

Aug 11, 2009 | Televison & Video

1 Answer

Tv wont turn on get audio then tv shuts off timer lite blinking


If TV stays in stand by with audio but no video, then common faults are the ballast board, or a fault on digital board.

If the led stays blinking , and tv turns off then the TV is on protect mode.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

Also ensure that the fault is not coming from a faulty receiver box sending bad signal, check if you get same problem with no receiver box or dvd connected.

If that does not work, and you keep having a flashing led on front of the TV, and tv turning off by itself after a while, that indicates a fault condition.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , startingthe flashing light.


If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

Common faults that can occur are a blown capacitor on power board, a convergence IC has blown, or a fault on Digital board.

Check also the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you can get same flashing state because of the video cable.


If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

Dec 21, 2008 | Mitsubishi WD-62531 Projection Television

1 Answer

Turns on, blinks 8 times, turns off


EIGHT Blinks---Problem with the audio (AUDIO), unit goes to standby and
blinks the self-diagnosis code. Check IC406 audio amp, PS401 and 402.

Feb 11, 2008 | Sony KP-53V90 53" Rear Projection...

1 Answer

No video, timer/stanby light blinks


I don't know if this will help or not, but I noticed mine starting to do the same thing lately, audio works fine when I turn the set on, but I get no video. I noticed that when I pull the front cover to get to the Light Intensity and Focus controls (G2 controls, I guess), and give just a slight turn on one of the knobs, the video comes on, but then I have to turn the knob back to where it was, to keep the colors right. It gets to be a real pain after a while...

If you have already had your set repaired, please share the solution!
Thanks.

Dec 15, 2007 | Sony KP-53XBR45 53" Rear Projection...

2 Answers

No picture blinking stand by light


I hve worked on a number of these units , your description is typical of a shorted blue picture tube. The protection circuits in the tv detect that there is a problem thus shutting the unit down to prevent further damage. Sony had a bad run of picture tubes in this series. The replacement cost of the tube is about $250 plus labor. My estimate would be for the repair about $400-500 depending on where you live and how honest your local technican is. I will caution you however, that you could replace this tube and the red or green could go. These would not be covered by the technicians warranty. When these sets are working, they have a superb picture and it is easy to get lured into fixing them. Scrivitron

Jun 13, 2007 | Sony KP-51HW40 51" Rear Projection...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69845 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6393 Answers

Are you a Pioneer Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...