Question about Sharp Aquos LC-32G4U 32 in. HD-Ready LCD Television

1 Answer

Thomson 40KW611S will not come on

When press power button on, it flashes green twice and nearly comes on but then goes to red flashing light. Televison will not come on now. It use to come on after trying this sequence a few times but no longer does. Im trying to find out has anybody else had this problem and if so what is the cause?

Posted by on

  • Anonymous Mar 07, 2009

    the ****** wont turn on.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 182 Answers

The flashing red light is an error code to assist the service engineer to diagnose the fault .the flashing is normally in 2 groups like 2 flashes then a pause and say 5 flashes

Posted on Jun 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sony bravia kdl-32bx300 wont turn on


https://community.sony.com/t5/Television-General/Red-light-blinks-6-times-tv-won-t-come-on/td-p/47107

Mar 14, 2016 | Flat Panel Televisions

1 Answer

Emerson lc320emx trouble turning on


You probably have an internal power supply problem

Mar 04, 2013 | Emerson LC320EM9 32 in. LCD HDTV

1 Answer

I have a Emerson 32" LC 320 EM1F, When I press power button, green light flashes 12 times then red light comes on and goes to standby. What seems to be the problem? How can I fix it?


It sounds that the main digital board has damaged. 12 blinks indicates it. if you wish to know more check this link for more details about 12 blinks to Emerson TVs

Jan 25, 2013 | Emerson Lc320em1f TV

1 Answer

Can set up th remote control for this tv with the direct tv cable remote


Here's how to scan for TV codes on your DIRECTV remote

1.Make sure your TV is turned on.

2.Slide the mode switch at top of remote to "TV".

3.Press and hold the MUTE button. This is located above the number 1 button.

4.While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.

5.Then enter 991, the green light on remote should flash twice.

5b. Press 1 again (it will flash twice again), then you press the power on button at the very top right.

6.Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.

*If you hit channel up very fast, you risk going past the code. Pressing channel down will back it up. I alway hit channel up very fast till the tv turns off, then back it up slowly till it comes back on.

7.When the TV powers off, press and release the SELECT button.

*Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

Mar 05, 2011 | Curtis LCD2425A TV

1 Answer

Power button flashes red. TV comes on momentarily


this is a inverter board defective. please change-it

Oct 31, 2009 | Panasonic TH37PX60 37 in. Plasma...

1 Answer

My Thomson 40kw611s will not work when I try my remote. The light flashes on the switch and it stays in standby mode. It is not the batterys,fuse or anything. Can you help?


If it starts flashing when you press the power button on the remote, the tv is getting the right signal from the remote. You have a problem inside the set.

Oct 14, 2009 | Sharp Aquos LC-32G4U 32 in. HD-Ready LCD...

1 Answer

Thomson 40KW611S - when switching set on, light flashes then goes into standby & cannot get to work.


this is an error code and directs the service engineer to where to lookfor the fault. I recomendyou contact a compertant service enginner to evaluate this fault for you as there are not much the layman can do.

Oct 11, 2009 | Sharp Aquos LC-32G4U 32 in. HD-Ready LCD...

1 Answer

Flashing red light


Same problem with my Sony. Unplugging for 36 hours solved the problem

Oct 05, 2008 | Sharp Aquos LC-37G4U 37 in. HD-Ready LCD...

1 Answer

Thomson 40KW611S


chances are the water has managed to get into the tuner.or worse onto the main signal board. if you are in the uk you can try www.tvs-services or call 01245302539 for part availability.
this is a job for a service engineer only.
Dont forget to get your aerial and cable replaced as it will happen again

Nov 21, 2007 | Sharp Aquos LC-32G4U 32 in. HD-Ready LCD...

Not finding what you are looking for?
Sharp Aquos LC-32G4U 32 in. HD-Ready LCD Television Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

68301 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

Are you a Sharp Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...