Question about Lexmark X75 All-In-One InkJet Printer

1 Answer

Is there a charge for this service - Lexmark X75 All-In-One InkJet Printer

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,120 Answers

No, this the free section of Fixya!

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

064 code


Symptom

E064 is indicated on the control panel. The error description is: The presence of a high voltage error is communicated by the composite power supply. The output for primary charging, developing, or transfer has deviated from a specific level of voltage.

Cause
* Adjustments in Service Mode are Incorrect
* Transport Assembly is Not Engaging Properly
* Dirty HVT Contacts for Developing Assembly and Charging Rollers
* A Paper Clip on HVT Contacts or Developing Assembly
* Faulty Transfer Roller
* Faulty Static Charge Eliminator
* Defective Composite Power Supply
* Defective DC Controller PCB Assembly

Action

1. Check the values in Service Mode and make sure they correspond to the Service
Label. If the copier receives a spike or surge through the 240V line these values can change (can also give you blank copies). Take particular note of the Dev Bias
setting. [COPIER > ADJUST > DEVELOP > DE-DC]
2. Make sure the Transport Assembly is engaging properly. The Transfer Roller should
make good contact with the drum. Check condition of screw (XB6-7501-007) and
Pressure Plates (FB5-4816-000 & FB5-4817-000) for the Transport Assembly.
3. Clean HVT contacts for Primary/ Transfer Charging Rollers and Developing
Assembly. Inspect for any paper clips.
4. Replace the Transfer Roller (FF6-0104-000).
5. Replace the Static Charge Eliminator (FF5-7246-000).
6. Replace Composite Power Supply followed by DC Controller PCB Assembly
Thanks

Dec 17, 2013 | Canon 2 Ir3300 Ir3300i B/w Copier/ Network...

1 Answer

Heater jacket was replaced by our local engineer who charged us RS.850 as cost of the jacket.Is this the genugine price. Regards. Ajay


If you were given a genuiene repair bill with the details mentioned of the heater then the cost must hold good which can also be included with the service charges.
If there was no bill given you can make a call to the local support center and report the matter or clarify as it is important that the service bill must contain all details.

Sep 01, 2011 | HP LaserJet 1020 Printer

1 Answer

I have a sharp2030 photocopier, how can i get find a solution if it prints out the blank papers .or what could be the problem. its says call for service F2? help


If you are getting no toner on the paper the charging unit which charges the paper to transer the image from the drum is faulty,Check all the removeable charging units which comprise a very fine wire stretched acos the paper path.Otherwise contact Sharp giving them service code

Apr 29, 2011 | Sharp SF 2020 Copier

1 Answer

Error e0610096 in canon 1140


The Service manual say:

E061 is an error code associated with the mechanism controlling the surface
potential of the drum, and points to the following:
(The notation "xx" of detail code indicates the color of the developing
assembly; e.g., xx=01: M, xx=02: Y, xx=03: Y, xx=04: Bk.)

Detail code: 0096
Description: Vd2 is 550 V or less.
Possible cause: The Vd2 lower limit is reached

Step 1
Checks: Is the setting of
COPIER>ADJUST>V-CONT-M/C/
Y/K in service mode identical to the
settings recorded on the service label?

Yes/No: NO

Action: Enter the settings from
the service label newly.

Step 2
Check the detail code in service
mode (COPIER>DISPLAY>ERR).
Is it 0000 or 0001? YES Go to step 3.
Is it 0010? YES Go to step 4.
Is it 0020? YES Go to step 5.
Is it 0030, 0031, or 0032? YES Go to step 9.
Is it 0040? YES Go to step 12.
Is it 0050, 0051, 0052, or 0053? YES Go to step 16.
Is it 0070, 0071, xx80, or xx81? YES Go to step 19.
Is it 0060 or 009x? YES Go to step 20.

Step 3: Potential sensor unit
Checks:
Turn on and off the power switch.
Does LED1 on the potential
measurement PCB remain on
during potential control?

NO - Replace the potential sensor unit.
YES - Check the wiring from the
DC driver PC to the potential
sensor. Turn off and then on
the power switch; if the error
is indicated once again, go to
step 2.

Step 4: Pre-exposure lamp
Checks:
Does the pre-exposure lamp turn
on during copying operation?

NO - Check the wiring from
the DC driver PCB to
the pre-exposure lamp;
if normal, replace the
pre-exposure lamp.

YES - Check the potential
sensor unit. Turn off and
then on the power switch;
if the error is indicated
once again, go to step 2.

Step 5: Primary charging assembly
Is the primary charging assembly
connected properly?
NO - Connect the assembly
properly.

Step 6: Primary charging assembly
Is the primary charging wire
broken or soiled?
YES - Clean or route the charging
wire once again. Turn off and
then on the power switch; if
the error is indicated once
again, go to step 2.

Step 7: Primary charging assembly
Are there traces of leakage on the
primary charging assembly?
YES - Replace the primary
charging assembly.

Step 8: High-voltage cable
Is there electrical conductivity
from the primary charging wire to
the high-voltage transformer
(HVT-DC)?
NO - Check the primary highvoltage
cable.
YES - Replace the HVT-DC
PCB. Turn off and then
on the power switch; if
the error is indicated
once again, go to step 2.

Step 9: HVT-DC PCB
Is the primary charging assembly
fitted properly?
NO - Fit the assembly
properly.

Step 10: Primary charging grid plate
Is the grid plate of the primary
charging assembly mounted
properly?
NO - Mount the grid plate
properly.

Step 11: High-voltage cable HVT-DC PCB
Is there electrical continuity from
the grid plate of the primary
charging assembly to the highvoltage
transformer (HVT-DC)?
NO - Check the grid highvoltage
cable.
YES - Replace the HVT-DC
PCB. Turn off and then
on the power switch; if
the error is indicated
once again, go to step 2.

Step 12: Post-cleaning charging assembly
Is the post-cleaning charging
assembly fitted properly?
NO - Fit the assembly
properly.

Step 13: Post-cleaning charging assembly
Is the post-cleaning charging wire
broken or soiled?
YES - Clean or fit the charging
wire properly.

Step 14: Post-cleaning charging assembly
Are there traces of leakage in the
post-cleaning charging assembly?
YES - Replace the postcleaning
charging
assembly.

Step 15: High-voltage cable
Is there electrical continuity from
the post-cleaning charging
assembly to the high-voltage
transformer (HVT-DC)?
NO - Check the post-cleaning
high-voltage cable.
YES - Replace the HVT-DC
PCB. Turn off and then
on the power switch; if
the error is indicated
once again, go to step 2.

Step 16: Laser exposure system
Is the movement of the laser shutter
normal?
NO - Check the shutter
assembly

Step 17: Laser exposure system
Is the dust-proofing glass or the
bending mirror soiled?
YES - Clean it.

Step 18: Laser exposure system
Is the laser power normal? (See the
descriptions given for how to adjust
the laser power.)
NO - Adjust the laser power.
If output is absent,
replace the laser unit or
the laser driver.

YES - Check the
photosensitive drum for
grounding; if normal,
replace the
photosensitive drum.
(After replacement,
execute the work under
II. C. 2.)
Turn off and then on the
power switch; if the
error is indicated once
again, go to step 2.

Jan 13, 2011 | Canon CLC 1140 Copier

1 Answer

SAVIN 2055 WITH AN SC301 CODE


SC301 error code description:
Charge Corona Output Error 2
Charge Current Leak

Charge would need to change number of pieces corona wire A166 9516 (to confirm with the service repair center) Charge Corona Wire.

Hope helps (remember to rate this)

Sep 30, 2010 | Savin Printers & Copiers

1 Answer

Hi there can somebody send me the service manual


You have to download the ir1018 Service Manual. from a download center.

There is a charge but it's not much though. Service manuals for Canon machines are never free - sorry. Good Luck.

Jun 18, 2010 | Canon IR1018J Black and White Copier

1 Answer

C 2101 on bizhub c451


this error code means there is charge cleaner malfunction. during the backword movement if the cleaner the home sensor was not actuated after a predetermined amount of time. to reset the error code leave the machine on and open then close the front door if the charge cleaner motor has been disabled in service mode this error code will happen at start up

Dec 11, 2009 | Konica Minolta Printers & Copiers

1 Answer

Stopped printing black


When I realized there is a charge for the FixYa services, I decided to contact Kodak directly. I am so GLAD I did. They were able to walk me through what needed to be done to correct the problem. Their service was timely, polite, and FREE! I suggest if anyone has the same issue, contact Kodak directly. Their customer service exceeded our expectations and I'm sure it will do the same for you.

To FixYa,
You may want to let people know up front that there is a charge. That way they can determine if they want to provide you with their personal contact information. I know that I NEVER would have signed up if I had know of the charges in advance. Because of that, I ask that you remove my information from your records.

Hope this helps someone else in the future.

Jul 26, 2008 | Kodak EASYSHARE 5300 All-In-One InkJet...

Not finding what you are looking for?
Lexmark X75 All-In-One InkJet Printer Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Printers & Copiers Experts

Roopesh S
Roopesh S

Level 2 Expert

228 Answers

Sanath Kumar V

Level 3 Expert

684 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Are you a Lexmark Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...