Question about Celestron 44345 Microscope

1 Answer

Celestron 44345 microscope screen will not turn on, there is a red light when you press the button and the screen is black

No response from the screen. Holding the button down only causes the red light to stay on longer. Any help would be appreciated.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Same Issue. Pleashe help somebody!

Posted on Dec 07, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Buffalo 120 pilot light will not stay lit when I release the red button


I would try holding the pilot light down for a lot longer. But you can also Try cleaning off the thermal couple or the flame sensor . Lightly use steel wool or a sand paper and clean off the probe without damaging it.

May 21, 2016 | Heating & Cooling

1 Answer

Samsung s3 phone wont turn on only red light stays on and a buzzing noise sounds and wont turn on need help


Shut it down by holding the power button until the screen goes black, don't tap the power off button, wait for the black screen. Then let your phone charge for a few hours (maybe over night) with power off and see if that helps.

Dec 12, 2014 | Samsung Galaxy S Iii S3 Gt-i9300 16gb...

1 Answer

Mod.Hp980PT, red and top green light flash, no heat


This is a very common feature on these types of simple, high-volume, low-cost home appliances known as a safety fault. This fault will temporarily (or permanently) disable the appliance and happens for several reasons: (1) an over-temp (high heat) occurrence, (2) an over-power (power surge) occurrence, (3) an under-power (power outage or trickle power) occurrence, (4) an over-time occurrence (auto-off fails), (5) a short-circuit occurrence (exposed/crossed/frayed wires, etc.). Fortunately, it uses a digital "fuse" system and can be reset by the user. However, there is no universal reset process on SoftHeat products so you just have to play with it until you figure it out (customer service dept is no help). Mine is a Kaz SoftHeat HP980PT, with a red power indicator/power-off button and 4 green heat setting buttons. Mine faulted after a heavy storm caused multiple power outages and power surges in my neighborhood. The green light on the highest heat setting button was flashing on mine. Here's how I fixed it: (1) unplugged both ends of power cord and straightened out the cord, then plugged back in to the heating pad end. (2) While holding down the flashing light button, I plugged back in to the wall outlet. (3) While still holding down the flashing light button, pressed and held down the red power-off button, then while still holding down the red power button, I released the flashing light button, followed by releasing the power-off button. This stopped the flashing green light and caused the red power indicator light to stay on (steady-on). It works fine now. Note: Some models have an actual hard fuse in addition to the digital fault feature or possibly only a simple fuse (without the digital fault system). These fuses can the found at many retail stores and then very easily replaced. I hope this helps some of you!!!

Jan 27, 2014 | Softheat Heating Pad HP218 12 3P

1 Answer

I have what looks to be an old monterey wall-mounted gas heater. the lighting instructions are illegible, and i have never lighted such a unit. i can't even find a model number on it. i need to light the...


look at gas valve, there should be a knob on valve, turn knob to pilot and push button in and hold, the silver tubing coming off valve follow it under the burner, as your holding pilot button down light the endunder burner, if flame appears hold pilpt button down for about a minute then change valve to on and pilot should stay lit, if pilot goes out redo and hold longer, the thermocouple may need to be cleaned.

Oct 27, 2009 | Heating & Cooling

1 Answer

Power up IMac but screen blank, fan on, light on but no response


I have one doing exactly this at the moment. It had gone to sleep and the fans were going like crazy. I think it is a Motherboard failure (it happened with many G5 iMacs), this one has been replaced once already, and I can't actually get it to install anything. I'm taking it apart tomorrow to see what I can find inside. If I fond anything I'll let you know.

Aug 07, 2009 | Apple iMac G5 Desktop

2 Answers

How to program an RCR460 remote


i have this remote and to enter the code manually you hold down the mode button (tv vcr etc) and while holding it in enter the code for the device. if the light for that device blinks and stays on then it accepted it. if all lights go off it didnt.

Jun 30, 2009 | RCA RCR460 Remote Control

1 Answer

Toshiba A105 keeps Restarting ---


maybe the power input is error
the uncorrect power input will result bad
or, it's your mobo broken

Jan 25, 2009 | Toshiba Satellite A105 Notebook

1 Answer

No Display output on the screen Nor the controllers power on


i heard that it could possibly be the power supply failed, i sent mine in 2 weeks ago cause it wasnt playing any games or anything, i get it back worked for about 4 days then is now not showing anything. But the best idea i can give you is to send it in

Oct 04, 2008 | Sony Playstation 3 (PS3) Console

5 Answers

Samsung lcd tv ltm1755b won't turn on (power light stays red)


I had a 26" Samsung LCD that wouldn't turn on, and the red light stayed on too, so I knew it was getting power. I found some info out there and figured out how to fix it. Also made a video to show others. I'm a complete newb so if I can do it, I know a lot of others can too. Make sure you research stuff and be safe when fixing it. I take no responsibility if you mess up your own TV! But like I said, I fixed it, so I figured almost anyone can. Also, it only cost me $1.40.

http://www.youtube.com/watch?v=vWKlex7kA7A

Feb 04, 2007 | Samsung LTM1755 17 in. HD-Ready LCD...

Not finding what you are looking for?
Celestron 44345 Microscope Logo

Related Topics:

581 people viewed this question

Ask a Question

Usually answered in minutes!

Top Celestron Science & Laboratory Experts

William McMath

Level 2 Expert

178 Answers

kakima

Level 3 Expert

102366 Answers

Tom Chichester

Level 3 Expert

34217 Answers

Are you a Celestron Science and Laboratory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...