Question about Office Equipment & Supplies

4 Answers

When changing toner module from red - black, copier will not work

Have a Kodak Ektaprint 235 copier. Has capability to swap black toner to red toner module. After swapping, copier will not leave an image. Had problem putting black back in, would not slide in very easy. Now there is no image. Machine runs paper through like it does work.

Posted by on

  • discountprin Jan 02, 2009

    The toner is not the problem. It had an image for a short while and now is faded to nothing.

  • discountprin Jan 03, 2009

    This is a big floor model copier and toner bottle is as big as some small desktop copiers. Toner is very available. It seems no one knows anything about a commercial copier of this nature.

×

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 19,396 Answers

If toner does not not slide in , then the toner carousel is not well in position.

Power cycle the machine, by closing it and unplugging power for few minutes, this often reports the carousel back in position.

Posted on Jan 09, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 326 Answers

It is due to the smoky cover on the image captaring optics.it needs to be cleaned.your toner and drum are very much okay and have nothing to do with this problem.just clean the optics and glasses to get back the printer to work.

Posted on Jan 05, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 104 Answers

Take out & gently shake the cartage left and right, up and down to scatter the ink powder and try again!

Posted on Jan 02, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 163 Answers

Its time to replace the old cartages with new one.

Posted on Jan 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pc-6re copies has black streaks down the entire page


Did you change the toner cartridge? If so, then check the fuser for a stripe on it which may be toner. Make sure the inside of the copier is clean. However your symptom sounds like a faulty toner cartridge. Try swapping it out.

Mar 05, 2011 | Canon Office Equipment & Supplies

1 Answer

I have a sharp ar-235 what does call service code U2-40 mean


CRUM chip communication trouble = the chip on the toner cartridge is faulty.

1, Try to clear the code press P, *, C, *, to enter the service simulation, on the key pad press 1,6, then the copy start, press execute on the screen.

2, Change the toner cartridge.
If it is a brand new one return to supplier as fault, if it is a refilled new one take back to supplier (the CRUM chip serves as a genuine supplies protection for sharp and 'blows' when the toner is empty the re-filler will have to put a new chip on it)

Nov 04, 2010 | Sharp AR-235 Copier

1 Answer

Brother HL-4070 printing out black whole page. Is this drum problem?


Try swapping the black and the magenta (red) cartridge.
This will not damage the printer and you can see if the toner or the drum is defective.

If you get a red page, drum
Black page, toner cartridge

Mar 26, 2010 | Brother HL-4070CDW Printer

1 Answer

Has a I54 code. goes on but goes into code after 10 seconds or so. Thanks Lawrence


there is a circut breaker switch in the back of the copier put it into (1)

Mar 19, 2010 | Kodak Ektaprint 95 Copier

1 Answer

Sharp AR 235, output light


You have to change the Developer in the developing unit. code is: AR271D
This procedure must be done by a copier tech.

Feb 15, 2010 | Sharp AR-235 Copier

1 Answer

Two red lights flashing under ink icon and yellow "E" flashing


E it measn the Printhead is not detected or printhead not installed., Its normal if you have E error that you will have 2 flashing red light check color ink or black.

Now try to reseat the printhead of the printer, YOu need to removed first the ink cartirdges before you can remove the printhead.

Now if you already reseat the printhead 2x and the ink cartridges It means the printhead is defective call Tech support for printhead replacement toll free 1 800 235 6325

Nov 12, 2009 | Kodak ESP 3 Multifunction Printer/ Copier/...

1 Answer

If this service costs please cancel this request immeditately. Thank you. I have a Kodak EKTAPRINT 95 Copier that has an error code E37 can you help solve this problem or tell me what it means?


GO ON LINE , TYPE IN ADDRESS BAR


KODAK CORPARATION
PICK USA
ASK QUESTION WHAT TYPE OF HELP YOU NEED
TECH SUPPORT,
CUSTOMER SERVICE MY HELP
LOCAL KADAK DEALER SALE THAT PRODUCT

CANDYMANGANDY

Jan 28, 2009 | Office Equipment & Supplies

1 Answer

Sharp ar-235 doble image in the copy


1.Might be a fuser problem. Check the upper fuser roller not to have toner on it.
2.The quenching lamp, if any, might be burn out.

Oct 19, 2008 | Office Equipment & Supplies

1 Answer

Won't print black


are you printing from the pc or standalone? if just from printer please try to uninstall reinstall the printhead then recalibrate it then do a deep clean of the printhead then try to print and see if there is improvement. if not...then that is a printhead issue
call kodak support 1-800-235-6325

Aug 04, 2008 | Kodak EASYSHARE 5500 All-In-One InkJet...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...