Question about Craftsman Electronic Reciprocating Saw In Plastic Case W/instructions & Blades

Open Question

Changing a blade on a craftsman elctronic reciprocating saw model 315171020

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
rowdy45176
  • 2176 Answers

SOURCE: Reciprocating saw-snapped blade-cannot be removed

What I would try is to spray some WD40 on the pin first and then see if you can find a small screwdriver or punch and try pushing the pin in further to release the broken blade. It doesn't sound as though it is anything major, maybe a burr on the side of the pin or possibly rust or debris. DON"T hit the pin because you might damage it or push it in and never get it back out. Looked at a diagram and it appears that they used roll pins to hold the clamp in place so it might be that one is cracked or mushroomed and you might have to drive them out. I suggest that you go to Searspartsdirect.com and type in your model number to look at the same diagram.

Posted on May 26, 2009

Ad
  • 384 Answers

SOURCE: Loose blade in reciprocating saw

Tighten the two setscrews that clamp against the blade.

Posted on Jun 15, 2009

  • 384 Answers

SOURCE: Reciprocating Saw / Stopped Working (No Response)

Many of my power tools that have stopped working, it has always been the "ON-OFF" switch that has been the proplem. Try blowing out the bugger, but watch that you don't loose some of the contacts. Never had brushes actually wear out, but did have one wire break off the brush.

Posted on Jun 24, 2009

SRF518
  • 232 Answers

SOURCE: Where to get a replacement quick change blade

have you tried Sears?

Posted on Oct 20, 2009

  • 57 Answers

SOURCE: blade stuck in reciprocating saw

The pin is probably stuck in the blade. This happens from time to time after they get dirty. Take some WD-40 or some other type of penetrating oil and spray a little in the blade holder while working the release lever. It will probably free right up.

Posted on Apr 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the tool-less blade clamp in a craftsman 8 amp reciprocating saw


Craftsman Reciprocating Saw replace the tool-less blade clamp

Jun 10, 2015 | Craftsman Saws

1 Answer

I have a Sears Craftsman reciprocating saw and do not know how to change the blade. Where can you find manuals for these? Model no. 172.171801


Hi there, Your saw is not listed but you can call this number and they may be able to help you.If your saw has rubber where the saw blade fits just push it back on the shaft and insert the blade they can face frontwards or backwards.If its an older model they had a set key tightened with an Allen wrench.Thank You for choosing FixYa.com. P.S. unplug or remove the battery when changing the blade.
Call (800) 252-1698 during these hours of operation:
Monday - Friday: 6:30 AM to 10:30 PM (CT) Saturday: 7 AM to 9:30 PM (CT) Sunday: 7:30 AM to 9:30 PM (CT)

Jun 24, 2011 | Saws

1 Answer

I was given a craftsman saws all. It seems to have a broken blade in place. Is there a site where i can view a manual? I'm not sure how to change blades with this tool


you might want to start with Searspartsdirect.com and with the model number you can view a parts explosion and then if there is a manual online you can click on it and it will take you to another site called managemyhome.com for a manual. Let me know if still having trouble

Jun 28, 2010 | Craftsman Reciprocating Saw Corded 8 Amp...

1 Answer

How do I remove the nose piece to repair the reciprocating shaft.


The gears are stripped internally in the saw...it will need to be repaired..

heatman101

May 12, 2010 | Craftsman 8 amp Reciprocating Saw with...

1 Answer

How to change the blade


look at front off saw , where blade is,there is a hex (allen) bolt, screw, or a lever on the side of saw

Apr 06, 2010 | Craftsman 8.0 amp Reciprocating Saw

1 Answer

How do you install the blade in the craftsman recipricating saw model 320


You need a allen wrench to remove the blade and to reinsall it look at the base of the blade and you will see an allen wrench. If there is no allen wrench then you must pull down on the clap assembly to release the blade. If you still can't figure it out here is sears web site where you can get help for it if you need a picuter.
http://www.searspartsdirect.com/partsdirect/index.action?psid=26128394&sid=PSx20071217x00001a

Sep 17, 2009 | Craftsman 8.0 amp Reciprocating Saw

2 Answers

Reciprocating Saw / Stopped Working (No Response)


Many of my power tools that have stopped working, it has always been the "ON-OFF" switch that has been the proplem. Try blowing out the bugger, but watch that you don't loose some of the contacts. Never had brushes actually wear out, but did have one wire break off the brush.

Jun 24, 2009 | Craftsman 8.0 amp Reciprocating Saw

Not finding what you are looking for?
Craftsman Electronic Reciprocating Saw In Plastic Case W/instructions & Blades Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Craftsman Saws Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Mike

Level 3 Expert

4339 Answers

Are you a Craftsman Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...