Question about Canon PIXMA MP160 All-In-One InkJet Printer

1 Answer

Waste ink absorber is full, waste ink full, waste ink absorber, a

Pixma 160
waste ink absorber is full, it will not allow to print

Posted by on

  • Anonymous Feb 25, 2009

    this is my problem : Waste ink absorber full, or platen waste ink absorber full.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 378 Answers

May the error code or how many blinking can solve your problem 

this is the list of error code 

How to clear Error Code Canon printers MP150 MP160
CANNON Printers MP150/MP160 ERROR CODE 


E2-2 No paper (ASF) 
E3-3 Paper jam 
E4 No ink 
E5-5 The ink cartridges are not installed or a non-supported ink cartridge is installed ,
or the ink cartridges are not installed properly 
E8 Waste ink absorber full, or platen waste ink absorber 
full

E9 The connected digital camera / video camera does not support Camera 
Direct Printing
E14 The Ink cartridges whose destination are wrong
E15 Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 Failed to scan head alignment sheet
E22 Carriage error
E23 Paper feed error
E24 Purge unit error
E25 ASF(cam) sensor error
E26 Internal temperature rise error
E27 Waste ink absorber full or platen waste ink absorber full
E28 Ink cartridge temperature rise error -
E29 EEPROM error
E33 Paper feed position error
E35 15 USB Host VBUD overcurrent error - USB
E37 17 Abnormal motor driver error
E40 20 Other hardware error 
E42 22 Scanner error





try this methode 

Methode 1

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting formenu selection)
4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED 
lights alternately in
orange and green, starting with orange.)
The number of the Reset
button pressing
LED Function Remarks

0 time Green Power off
1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset See waste ink counter reset
procedures below.
5 times Orange Destination setting See Destination setting
procedures below.
6 times Green Print head deep cleaning
11 times Orange Button / LCD checking
12 or more times Returns to a menu selection


that's all


maybe it can fix your problem



thanks 

Posted on Jan 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A printer,s ink pad is at the end of its service life


This means the waste ink collection sponge is full. This counter can be reset but it is strongly recommended to replace the ink pad as you will end up with a large amount of ink spilt on your desk if you continue to use the printer after the pads lifespan. It can be quite a large job to change depending on the model. If the printer is not an expensive model it may be more cost effective and less messy to simply replace it with a similar model.

Jan 14, 2017 | The Office Equipment & Supplies

1 Answer

5C00 Error Code as well as yellow and green alternating lights


To fix this error is much easier than it looks. Unplug the printer power. Move the ink cartridge cradle to the left. Over to the right you will see a small pad about 1cm square. This pad and the area around should be covered with ink. Get a cloth and press down on this pad - it's not fixed so should come away with the cloth, otherwise use tweezers gently. Squeeze the pad several times between your thumb and forefinger while inside the microfibre cloth to remove ink build up. Then when not much ink comes out on the cloth, clean the area in the printer around the pad so that looks free from ink too. Then position the pad back in place, move the cradle back into position, plug in and switch on - should work fine now.

Jan 14, 2017 | Office Equipment & Supplies

1 Answer

B&w/gray Scanning Is Okay But Color Scanning Problem


Run ink head cleaner routine. If you cannot the list make and model of printer. Thanks.

Dec 25, 2014 | Office Equipment & Supplies

3 Answers

My Epson WF-3640 is printing with gaps in the text. How do I fix this issue?


Make sure you should remove shipping tape from the ink cartridge. These taps are used to protect printer during shipping but you have to remove it before starting printing. Beacuse these taps prevent the ink to entering in print head. If you will not found shipping tape in your printer then there is terr off strip, remove it. The tear off strip seals the the vent holes on the top of the cartridge to prevent it from drying out on the shelf or during shipping.
After ensuring that the shipping tape has been removed, run the printer's "Head Cleaning" utility to prime the cartridge, then print a test page.
See full detail at- http://guideusermanual.com/product-name-workforce-wf-3640-manual&po=152836&lang=English

Sep 18, 2014 | Epson WorkForce WF-3640 Wireless Color...

1 Answer

Why is print quality poor after inserting new ink. Copies are faint and have lines


the cartridge is clogged with ink that has dried and reduced the slit. you need to replace the cartridge with a new one. it happens usually if you recharge the cartridge 3 or 4 times with compatible ink.

May 07, 2014 | Office Equipment & Supplies

1 Answer

How to clean ink absorber for canon mp237


First of all open the ink cartridge of your printer.
When the ink cartridge would move all the way over, then disconnect the power cord of your printer.
Now pull the frame of rubber from the printer and remove ink pads.
To clean ink pads you may place them in a bowl having warm water and start rubbing and squeezing them to clean it from ink.
After removal of ink, keep the pads separate for dry.
When the pads get dry completely, place them back in rubber frame.
Reinstall the rubber frame in your printer.
For deep guide and support refer to-
Canon Pixma Mp237 Manual

Oct 07, 2013 | Canon PIXMA MP230 Multifunction color...

1 Answer

Prinnter not printing but showing 'put custom in manual tray'


There is still a print job in the queue. Place a sheet so it prints or kill the job.


Open Printers and Faxes. Open printer. Highlight jobs and Right click > Cancel, or Documents > Cancel.
For those stubborn jobs, Right click My Computer > Manage. Choose Services and Applications > Services > Print Spooler. Right click and stop. Then start. This may have to be done from the Print Server if it's network printer. Contact IT to kill.

Nov 09, 2012 | Office Equipment & Supplies

6 Answers

Printer won't recognize cartridge


I had the same problem. I'm not sure but I think I replaced the cartridges when the printer was on because I turned the printer off and removed one of the cartridges. When I turned the printer back on it recognized that cartridge but not the others. I turned the printer off again, rmoved all cartiridges and put them back in when the printer was still off. When I turned the printer on again I had no problems. So...try turning off the printer, rmove all cartridges, then put them back in and restart printer. Hope this works for you .

Nov 28, 2007 | Epson Stylus 2200 InkJet Photo Printer

Not finding what you are looking for?
Canon PIXMA  MP160 All-In-One InkJet Printer Logo

1,080 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

98868 Answers

old marine
old marine

Level 3 Expert

1573 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...