Question about JVC AV-48WP30 48" Rear Projection Television

1 Answer

Blue power light flashing and TV not working

7 days out of warranty and TV shut down today and not coming back on. Blue power light flashing now. Nothing in manual about this. Called customer care service and of coarse they dont tell ya whet it means they just refer u to a tech so u can pay them to tell ya. if any one know please get respond, thanks, jb

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 14 Answers

It sounds like you have a blown lamp. On average i have seen lamps on JVCs cost about $200

Posted on May 13, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv will not turn on i push power on button and blue lights click on an tv acts like it will come on but then tv shuts off and no picture appears


The blue light merely indicates power is getting to the TV. When you press the power on button, the defective power supply shuts the TV down immediately

Jan 06, 2013 | JVC LT42P789 42 in. LCD TV

4 Answers

Hi I have a Pioneer PDP-436XDE its over 3 years old and has worked perfectly until today when it switched itself off and would not switch back on. Ive unplugged it from the mains and left it for some time...


The reason for your tv not switching on properly may be due to

The main filter capacitor or other filter capacitors in the low voltage power supply is dried up and this can cause all kinds of regulation problems.

The power supply regulator is defective (or marginal) allowing excessive voltage on its output and then the X-ray protection circuitry shuts you down.

blue or red colour may be due to fault in chroma decoder circuitry.

Jul 05, 2008 | Pioneer Televison & Video

1 Answer

My Hitachi L42VC04UB replaced a failed power board .The television comes on and after a short time it shuts down and the standby light in the front of the television flashes blue and red .This happe


Well either the TV's main (or other) board overloads the power board and it shuts itself off or the power board itself shuts itself off for whatever reason or the main board shuts off for whatever reason.

With the setup you have I'd say it's probably going to be difficult to figure out which one it is.

You will want to have yet another board - either main or power - to eliminate one of the two most likely possibilities.

What did you do with the original power board?

If you keep it you can probably send it to us for repair....or if it's cheap enough just buy another one.

i don't think there's an easier and affordable way to narrow it down than using a third board.

www.coppelltvrepair.com

Oct 08, 2012 | Televison & Video

1 Answer

Heard a pop and screen went blank - won't come back on.


Your Lcd Projector Lamp/DLP Television Lamp went out

its about $165-$200 to replace if not under warranty


Nov 28, 2008 | Hitachi Televison & Video

20 Answers

Lcd sharp tv flashing green light


Try unplugging the unit and while unit is unplugged hold the volume up button and channel down buttons down and while depressing both buttons plug the unit in. Let go of the buttons and the unit should come on in the service mode. There will be a small k on the screen. With the sharp remote press the channel up button once. This should bring up a menu that will show a lamp error line. If the lamp error is = to 5 the unit is in lamp error shut down. User channel down to highlight that line and curser right arrow to highlight the lamp error #. Hit the enter button to clear the lamp errors. Now unplug the unit and let it sit for a minute and plug back in. I hope this corrects the problem. If the unit does not come on by doing this or if it does and you do not find lamp errors the power supply pcb may have been damaged by the surge.

Jan 06, 2008 | Sharp Aquos LC-37G4U 37 in. HD-Ready LCD...

2 Answers

No picture or sound


hi guys! i have a tn61x81 and the probleme with this tv is when i plug the tv the tv try to open but shut down y try to push the power botom it's make no difference the light near the power botom is flashing no power no image no sound noting. i think it's the power suply but i'm not realy shure. if aneyone can help me it will be realy apreciate.

Oct 29, 2007 | Toshiba TN61X81 61" Rear Projection...

2 Answers

Tv shut off and wont come back on


Your TV is going into some kind of a protection shutdown. In todays tvs just about anything wrong anywhere and the tv will do what it is doing. Unfortunatley there is probably little you can do yourself to track it down, probably need a pro.

May 09, 2007 | JVC AV-48WP30 48" Rear Projection...

Not finding what you are looking for?
JVC AV-48WP30 48" Rear Projection Television Logo

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75888 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...