Unable to access DLink WBR 2310 Configuration page
Hi i have a Westell modem and a DSL connection.I recently bought a DLink WBR 2310 Rangebooster wireless router. The problem is that i cannot access the router configuration page.When i type in 192.168.0.1 or http://192.168.0.1 , the message is that page cannot be dispayed.
I even tried assigning a static IP to my computer and then accessing the router configuration page but it did not help. Anyone got a solution to this?
Re: Unable to access DLink WBR 2310 Configuration page
Reset the router first, press the reset pinhole on the back for 10 seconds using a paper clip, don't press it too much or it will mess up the settings of the router. then try to access again the configuration page.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Who is you ISP? if you're using cable connection follow these steps:
1. Connect modem to WAN port of the WBR-2310 2. Connect computer to port 1 of the WBR-2310 3. Open web browser (IE, firefox,chrome,safari), and type in 192.168.0.1 into your address bar 4.Into the log-in page username:admin password: (none) 5.click on "SETUP" 6. Click on "MANUAL CONFIGURE" 7..in the Internet connection type, make sure that it must be in DYNAMIC IP DHCP 8. Click on CLONE YOUR PC's MAC ADDRESS button(notice that mac address will change after you click on that button) 9. Click on SAVE settings now and it will count down click on Continue after that 10. Then Try to ACCESS Internet
/... but if still you cannot access Internet try to power cycle the modem and the router.. follow these steps also
1. turn off bothe modem and router (just unplug the power cord) 2. after 1 minute, TURN ON first the modem, 3. after 1 minute again, TURN ON the router 4. after 1 minute try to access Internet
But if still no Internet connection, please look for the brand of your modem if it is speedstream 5100 or hugesnet or actiontec modem because those modem have the same IP address with your DLINK router and you need to change the IP address of your DLink then....
Further questions? call 1-877-453-5465 (US), 1-800-361-5265
connect your computer to the router by an ethernet cable. Open Internet explorer or FIREFOX. Type the roiuter's default IP-address (if not known: its either 192.168.0.1 or 192.168.1.1 or 192.168.0.0 or 192.168.1.0... keep trying until you're answered and asked for the password to enter the router (either attached on the router, in the manual or try: user: admin password: admin or password: password. Whgen you're in you'll find many checkboxes you could fill oput or notr; Easyway: give your net a name (SSID), then choose the network access security (set it to wpa-psk), choose a password and enable DHCP (then the router does the rest). Disconnect, look if the computer sjhows reception of your netwoirk by displaying its name. then connect. You will be asked for the password you chose. Done.
I assme you have a DSL or cable modem from Comcast and this is connected to the wall. The LAN cable from this modem should now be connected to the WAN/Internet port on the DLink wireless router.
To secure your wireless network please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security
You can set up the router without the CD also. If you connect the computer to the modem it works, right ? Now you can connect the computer to the router and the modem to the rotuer . Access the router set up and set up the router. Click Here for step by step instructions
The IP address 192.168.0.1 you use with your browser is not to get into the Dlink WEB page, it is to get into the DLink router configuration, to set up the router and wireless security eg. network SSID, turn off SSID brocast, WEP/WAP encryption, MAC address filtering etc.
Connect one of your computer to LAN port 1, connect the modem to port WAN section, access the configuration page 192.168.0.1, configure the router as dynamic IP address under settings, then check the IP address under status (WAN section) if you have the IP address it means that your connected.
I'm pretty sure that downgrading the firmware to 1.0.3 will work. I had been running at this level for quite some time and for some reason I decided to upgrade to the latest version which started the problems for me. I am downgrading to this now and I expect better results. All of the firmware versions are available at http://www.dlink.com/products/support.asp?pid=470&sec=0. You pick the right hardware revision. PLEASE NOTE: Save off/remember your settings as when you change the firmware it resets all of them back to system defaults.
what is your connection to the dlink router look like, plz define. If you think your connection settings are fine then try resetting (do this if you do not care about the settings on the router) the router to default settings by depressing the small hole at the back of router for few seconds and it will refresh the router to default settings. Try connecting now to an ethernet cable and it should work if not then you have to go into router settings and match the ISP provided settings for modem to work in the router configuration. For going into the router make sure you have the manual for it: http://www.dlink.com/products/support.asp?pid=478&sec=0
select the model and download the manual as well as any firmware.
Hope that helped