Question about Panasonic PT-50LC13 50" Rear Projection HDTV

1 Answer

PT 50LC13. Sound but no picture

I don't think it is the lamp as the other displays seem to work (i.e. set up, adjusting picture, video and the notations in the top corner indicating RGD, Videpo, Component, etc.) Just stopped working today.

Posted by on

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 108 Answers

Unplug the set fro about a minute or two and see if that clears the error. If you are using a surround amp that yoir video sources pass through before it gets to the tv then make sure that is set to the right input and working properly and finally make sure the source providing the signal is working. If all is good then you have an issue on your main board where the video switching is processed.

Posted on Jan 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic pt-50lc13 won't show picture. Blinks green when turned on can hear lamp clicking then goes off to red blinking for a few miniutes then shuts down to just red . Can u help me out please?


sound like your lamp is bad ...Panasonic TY-LA1000 Lamp Replacement...Ballast Repair Kit for Panasonic PT-50LC13 some time the ballast go bad as well to hear bouth part number one lamp and 2 ballast I hope this help you..

Nov 19, 2013 | Projection Televisions

1 Answer

Panasonic PT-50LC13 50 blinks 8 times at power button


hi, make sure the lamp is fitted securely and the lamp cover as well you may need to reset the lamp counter hope it helps

regards
shaun

Nov 27, 2011 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Lamp power supply board on Panasonic PT-50LC13 mulfunction.


You can purchase the lamp supply thru "Encompassparts.com... The cost is $100.00, there is a $250.00 core charge on that module, so when you return the old they refund the 250. Initial investment will be 350.23 then take the 250. off that. That will be the end cost.

Part # LSEB3087A

Apr 16, 2009 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Sound but no picture I don't think it is the lamp as the other displays seem to work (i.e. set up, adjusting picture, video and the notations in the top corner indicating RGD, Video, Component, etc.) I...


Well, If you see on-screen display and Menu on TV screen that shows problem is with connections wires of DVD Player etc. Also check Cable connector at rear of TV.
One more trick it to unplug TV from AC outlet for couple of minutes and replug back in and power it up. Hope this will fix TV problem.

Feb 14, 2009 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Reset Time Problem on Panasonic TV (PT-50LC13)


Power on the set, listen for afaint buzzing sound as the set tries to fire up. If you do not here it then your lamp driver, or ballast is most likely faulty. Also make sure you have the door and all covers back in place and secure. And make sure you insatlled an orginal panasonic lamp because some generic will not work.

Jan 06, 2009 | Panasonic PT-50LC13 50" Rear Projection...

2 Answers

How to reset the meter of lamp


You need to have your Panasonic remote.
1. Make sure the power cord is plugged into a properly grounded outlet and turn on the set with the power button on the projection unit or the remote control.

2. While holding down the (VOL -) key on the projection unit press the PIP or SPLIT key at the same time. Hold it for longer than 5 Seconds. The PIP or SPLIT key is model specific:

PIP for Models:
PT-50LC13/PT-60LC13/PT-50LCX63/
PT-60LCX63/PT-43LCX64/
PT-50LCX64/PT-60LCX64

SPLIT for Models:
PT-43LC14/PT-50LC14/PT-60LC14



3. When the unit resets the lamp timer it will display a screen on the TV indicating it was reset to zero. You press recall on the remote to exit.


You will find a PDF of the instructions at this site:
http://fixyourdlp.com/blog/wp-content/uploads/2007/09/panasonic-tyla1000-lamp-instructions.pdf



Aug 23, 2008 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

PT-50LC13


It could be the ballast that is bad. A bad ballast also shortens the Lamp life .

Jun 23, 2008 | Panasonic PT-50LC13 50" Rear Projection...

5 Answers

Panasonic pt-50lc13 shutting off


i'm on my 3rd bulb in 5 yrs. i hate this tv. this time my bulb light didn't come on. instead the power light flashed green fast then went to red flashing after. i took out the bulb and it's blown!

Nov 19, 2007 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

Sound problems on PT 50LC13


try unpluging and plug back in, same on cable box if you have one i have had calls with no sound and found cable box is the problem just unplug for about 30 sec and plug back in

Oct 06, 2007 | Panasonic PT-50LC13 50" Rear Projection...

Not finding what you are looking for?
Panasonic PT-50LC13 50" Rear Projection HDTV Logo

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

The Knight
The Knight

Level 3 Expert

68250 Answers

Are you a Panasonic Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...