Question about HP C4170-90959 Service Manual -15754

1 Answer

HP 9500n Colour Laserjet

All four colours are misaligned. registration of all colors out.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 2,985 Answers
Re: HP 9500n Colour Laserjet

The printer software should include a realignment tool,check the manual and E-mail HP Support

Posted on May 09, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My HP Color LaserJet 8550 is printing very distinct streaks. It seems to be in areas that have a lot of magenta. Any idea how to get rid of the streaks??

If the streaks are limited to a single colour, the problem is likely to be THAT colour TONER CARTRIDGE.

A problem with the DRUM UNIT (only a single drum in this printer) or the TRASNSFER DRUM , or BELT (this printer has both a transfer drum and a belt), would affect ALL colours.

Apr 23, 2012 | HP Color LaserJet 8550 Printer

1 Answer

There was bits of paper, from a stuck edge from a sheet of business cards that I think are perhaps still in the printer. When I print a colour sheet the alignment is off, printing black and white seems OK.

What do you mean by alignment?
If you mean that the colours are misaligned, run a full calibration. Repeat it three times and then try your printing.
If bits of the business cards were left in the printer - it should affect the colour printing as well as B + W. You would also be getting paper jams.

Oct 25, 2010 | HP Color LaserJet 2600n Printer

2 Answers

Xerox DocuColor 4CP printer will not print colour. It will print black fine though. Have defaulted printer and printed colour page, still no colour, just black.

According to this site, Windows 7 drivers are available for the Xerox Docucolor 4CP printer.
What operating system are you using?
Also, is it possible that your color toner has been depleted?

Jul 18, 2010 | Xerox Printers & Copiers

1 Answer

Define 54.18 ERROR code on a Hp Laserjet 5500

According to the HP Service manual, there is no 54.18 error.

The listed errors are:

54.1 Temperature error
Check the fuser. See 50.X fuser error.
54.3 Image density sensor error
Check the connections. Replace the color registration detection assembly.
54.5 Colour registration sensor error
Check the connections. Replace the color registration detection assembly.
54.6 Image density error
Check the connections. Replace the color registration detection assembly.
54.7(Y), 54.8(M), 54.9(C), or 54.10(K) Drum phase sensor error
Check the connections. Replace the drum phase sensor for the indicated color.
54.11(K), 54.12(C), 54.13(M), or 54.14(Y) Toner sensor error
Check the connections. Check the cartridge and replace it if necessary.
Replace the color registration detection assembly.
54.19 Transfer Belt error
Check the ETB connection. Replace the ETB. Replace the DC controller.

It is most likely that you have a faulty Toner Cartridge.

Jun 21, 2010 | HP Color LaserJet 5500 Printer

1 Answer

Color print does not line up blue is printed off center of red but black is fine.

Make sure you have the latest Firmware installed on your printer, this can be found at HP.COM/SUPPORT/CLJ2605. It sounds as though the problem you are experiencing is Colour Pane Registration problems. If you have the latest Firmware, then tryturning on Registration (Configure Device>Print Quality>Optimize) and perform 3 calibrations in a row. If the calibrations take more than a few minutes each, check the error log (Diagnostics>Print error log) for any CPR errors. You may need a replacement Laser unit.

Nov 19, 2009 | HP LaserJet 2605DTN Color Printer

1 Answer

HP Color LaserJet 2600n - cannot find how to change from colour printing to greyscale - Help

this option you will get in printer properties in prefrence and colour option.

Nov 16, 2009 | HP Color LaserJet 2600n Printer

2 Answers

Hp color laserjet 2600 n it will not let me print

There is an override sequence and it works well. Press the select button (checkmark) to indicate Main menu. Press right-arrow (RA) to select System Setup. Press Select , then RA to Print Quality, Hit select. RA to Replace supplies and hit Select. Now, RA to Override Out and Select. Confirm with Select again. Your 2600n will now run even with an empty toner cartridge.

Jul 08, 2009 | HP Color LaserJet 2600n Printer

2 Answers

HP 1600 Colour laserjet Double image

Colour registration problem (some printer loose their registration from time to time).

There will be an option somewhere in the menu system of the printer, or the HP 'Toolbox' to correct this.

Apr 04, 2009 | HP Color LaserJet 2600n Printer

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts


Level 3 Expert

94113 Answers


Level 3 Expert

7983 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides