Question about Frigidaire PLD4375RFC Dishwasher

2 Answers

Our 6 month old frigidaire dishwasher model #pld 4375 rfc just diplayed the ER S code.... help?

Posted by on

  • 1 more comment 
  • castle19 Jan 04, 2009

    DId you ever fond a solution? mine says the same error message.

  • SandyB2 Mar 01, 2009

    Same problem here - Model PLD4375RFC2. Purchased in May of 2008 - ER light is blinking, along with WASHING, DRYING and CLEAN S lights. This is one week after our Frigidaire microwave stopped working because of a switch. It's in the middle of repair right now - waiting on parts for the board so they can replace it. We bought a Frigidaire refrigerator as well - all at the same time - so now we're concerned that this may be a problem with their products. So our dishwasher and microwave, both from Frigidaire, are out of service and less than nine months old.

  • Anonymous Apr 08, 2009

    Just to update everyone, the tech came to our house and said that the computer in the control board needed to be replaced. We're STILL waiting for the part to come in. Ridiculous.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

My unit has the same problem and it is due to a failure of the control board. The tech that came to look at it tells me that this unit vents from the top of the tub rather than from the front, and he claims that the installation instructions require a 1" gap between the top of the tub and the countertop.

Now I have found no such information in the installation manual that I downloaded, and I am skeptical that a 1" gap could be done, and if it could it wouldn't look to good.

I am going to pull my unit out and see exactly where the vent fan is and what the clearance is. The service tech says they can't replace the control panel until the installation is proper. I am thinking this is at least to some extent a design flaw with this machine. There seem to be a lot of reports of this failure.


Posted on Apr 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Nope - not yet. I'm going to try calling tech support and see what they say.

Posted on Mar 01, 2009

  • SandyB2 Mar 01, 2009

    Sorry - I posted this as a solution. I'm new to the board! I'll let you know if I find anything out.

  • SandyB2 Mar 01, 2009

    We tried starting it up again, but it's just not working. When I call Tech support tomorrow, I'll let you know what I find out.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Frigidaire dishwasher reads Er clean


http://www.appliancerepairlesson.com/2012/12/15/frigidaire-dishwasher-error-code-er-keypad-code
It could be thinking you are pressing a button for too long.
Try the above link answer for reset.
Or unfortunately it can be a shorted keypad.

Dec 01, 2015 | Frigidaire Dishwashers

1 Answer

How do I reset my Frigidaire dishwasher? eR light is flashing


Good Afternoon Sammy, thank you for your inquiry!

Based off the information you have provided you would like to reset your Frigidaire dishwasher because it is flashing "ER". The best way to reset your dishwasher is to flip the household circuit breaker off for roughly ten minutes. If you continue to receive the "ER" code it could be a possible problem with your main control board or keypad. I hope this is helpful information. -Matt

Mar 21, 2015 | Frigidaire Dishwashers

2 Answers

How do I find out the error codes?


Good Afternoon Delia Collins, thank you for your post!

Based off the information you have provided your Frigidaire dishwasher is flashing an "ER" error code on the panel. Typically, the "ER" stands for an error code sometimes to help clear out a false error code you can perform a reset on your dishwasher. In order to do that you would need to disconnect power from your dishwasher for approximately ten minutes.

If you continue to experience an issue with the error code I would recommend contacting a technician for proper repairs. The technician will be able to properly diagnosis your dishwasher and this will help you to avoid any unnecessary part purchases. Hopefully this is helpful. -Matt

Nov 05, 2014 | Frigidaire Dishwashers

1 Answer

Have a Frigidaire Gallery dishwasher that is flashing ER


Good Morning Jimpat Holmes, thank you for your inquiry!

I understand that you are having an error code "ER" displayed on the panel of your Frigidaire dishwasher. Normally, "ER" stands for error code and that can be a miscommunication within the board. I would perform a reset on your dishwasher and you can do that by disconnecting power from your dishwasher for ten minutes. If you continue to receive an error code you could be experiencing an issue within the control panel or faulty wiring harness. I hope this information is helpful. -Matt

Oct 30, 2014 | Dishwashers

1 Answer

Er S flashing How to fix


Not sure what the "S" is, but on a Frigidaire, the Er fault code is caused by a stuck key on the console. You'll probably need to replace it:

Replacement Console asse 807545702 for FRIGIDAIRE Large Kitchen...

Oct 19, 2014 | Frigidaire Dishwashers

1 Answer

4yr old Frigidaire, green flashing ER light and red flashing washing/drying and red flashing clean/S. model# PLD 4555RFC3. Also green flashing china/crystal and red flashing rinse/low, start/delay doesn't...


Good Afternoon Sandra, thank you for your question!

Let's try resetting the dishwasher by either unplugging it or flipping the household circuit breaker to the off position. It is important to wait roughly ten minutes and then turn dishwasher back on. Confirm that the door is properly latched and try selecting a cycle. If resetting the power does not correct the issue, it could potentially mean a number of things: a potential wiring failure, damaged cord, faulty door latch assembly or control board. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair the appliance.

Sep 21, 2013 | Frigidaire 24 in. FDB1050REC Stainless...

1 Answer

ER code, flashing touch pad selections.


It is most likely a fault with the keypad mebrane on the dishwasher control panel. Need model number of dishwasher to make a more detailed conclusion.

Jan 04, 2013 | Frigidaire Dishwashers

2 Answers

I have a Frigidaire model#PLD4555RFCO the er code and the washing and drying and clean and S lights are on and blinking on the display. have any ideas what the problem is?


Hi

"Er Clean S" is a common error with Frigidaire which means shorted keypad. The issue is with the touchpad/keypad that should be replaced. However, before replacing the keypad you can unplug it and take it apart completely and use a hair dryer to blow some warm air on the keypad assembly to blow the moisture off. Hope this helps...please post back for further assistance.

Daniel

Aug 27, 2011 | Frigidaire Professional Series 24 in....

9 Answers

Dishwasher er error code


I have a similar problem with my Frigidaire FDB4050LHS1. My Owner's Manual says to contact the Customer Care Center if the display shows "Er", "uF", or "CE". When I called them, Maria didn't have a clue what the codes meant - all she could do was give me phone numbers to authorized service centers in my area.

I managed to get ahold of a "SERVICE DATASHEET" P/N: 154718601. The error code "ER/ER" means there is a "switch failure"; "ER/CE" denotes a "Configuration Error"; "ER/uo" means "Vent will not close"; and "ER/UF" means "Fan not running".

The schematic only labels three switches - labeled "USER INTERFACE SWITCH", "DOOR SWITCH", and "FLOAT SWITCH". There is also a switch in the pump motor assembly. If either the door or user interface switch is faulty, then you probably won't be able to do anything other than call a repair service - unless you know how to replace these switches yourself.

If the float switch is causing the error, you might be able to run the "Water/Service Test". From "PF" (denoting a Power Failure) or idle mode (with no lights on whatsoever), press and hold the "DRY/AIRDRY" and "START/CANCEL" buttons at the same time for 3 seconds. This will start an 8-stage test that runs for about 7 and 1/2 minutes. The display will show which step the test is in until it shows an error code. Step 1 tests the water valve, which is where the float switch is located. If that switch is bad, you will likely see "Uo" displayed within the first minute of the test.

Aug 24, 2008 | Frigidaire 24 in. FDB1050REC Stainless...

Not finding what you are looking for?
Frigidaire PLD4375RFC Dishwasher Logo

Related Topics:

459 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...