Question about Bathtubs & Whirlpools

1 Answer

Humidity controls for my refrigerator

My frig has bins to control the humidity inside them.
The trouble is that I don't know if the humidity should be high or low for fruits or veggies...
Can you help?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 33 Answers

High humidity for veggies!
Low humidity for fruits!

Posted on Jan 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an Aqua Glass Jaccuzzi that I haven't used in 10 years. The last time it was used it worked perfectly. Now I can't turn it on at all. I don't remember is just the round dial that


Check the circuit breaker and make sure you have power to the pump.
If you have power to the pump and it is not operational when the tub is full of water and you are in it then I would say you have a serious problem.
Most all of the older control that Aquaglass has used in the past have been discontinued.
You may want to visit this link and identify your control before you begin t trouble shoot your system.

Rod
US Parts Center
888-521-6183

Feb 27, 2013 | Whirlpool Safety Bath Walk In Bathtub -...

2 Answers

We don't know how to operate our maax hydromax system. We moved into our house and the tub has never worked. We get a message no h2o and then sometimes it will do a countdown from 10. Is there a


This sounds as if the low water sensor may not be working. They are designed to know when the tub has water in it and then the motor will start.
What is the model number of the control box under the tub that the pump plugs into?
If we can figure out the control then we can find a solution for you.

Rod
www.uspartscenter.com

Jan 27, 2013 | Maax Bathtubs & Whirlpools

1 Answer

It wont run no lites or any thing. has power into control panal.nothing hums buzzes or any thing,want a diagram to figure this out,model number 12-322-322m thank you this is a seven sea hot tub


The wiring diagram for most control boxes made today are located on the inside panel of the control box.
If this doesn't blow the circuit breaker when you turn the GFCI on then you most likely have a bad circuit board.
US Parts Center

Aug 17, 2011 | Bathtubs & Whirlpools

1 Answer

Pump will not turn on and all power has been checked....is there a switch on the pump itself?


Almost all motors like this have an internal limit switch that will "pop" when it gets to hot or stuck. It should be on the end and is small - less than a 1/4" most likely red. Just push it back in.

If it doesn't have a visible button then it should reset by itself in 30 min or when it cools down.

If these don't solve the problem it could be the motors bad.

Let me know if you need any more help trouble shooting it.

Jun 30, 2011 | Bathtubs & Whirlpools

1 Answer

I have a Lifestyles Phoenix Spa with a Wolfpac model 12404GH controller. The onboard circuit breaker trips when the temperature control potentiometer-knob is turned up past water temperature and when the...


IF when the spa control calls for heat and it trips the breaker when the heater comes on then you have a bad heating element and it will need to be changed.
Disconnect the power to the spa. Disconnect the two wires going to the heater and then turn the spa back on.
If the spa stays running without the heater attached then that will be your source of trouble. New heater and you will be all fixed up.

Jan 28, 2011 | Bathtubs & Whirlpools

2 Answers

I have a MAAX Hydromax - not sure about the model #. The blower and circulation pump no longer engage. At first the problem was intermittent now it will not work at all. I tried to trouble shoot the...


yes. search US Parts Center for a solution. They will want to know the model number of your pump and model number of the controls you have.
Most likely it is a bad circuit board in the control box that turns the pump/blower on/off.

Jan 25, 2011 | Bathtubs & Whirlpools

1 Answer

WE have an older outside model JACUCCI brand hot


Try hitting the reset button in the control box, and let me know if it fixes it it's red. And inside the timer control pannel.

Aug 06, 2009 | Bathtubs & Whirlpools

2 Answers

"Jacuzzi j-400 series" hot tub- F1 code flashes on control panel


Your circulation pump isn't working you should see the flow awitch closing if you have the visible model and hear the pump running.. If its the smaller circulation pump model it needs replacing

May 18, 2009 | Jacuzzi Bath Nova H530 917 Black Soaking...

1 Answer

Freezer stays warmer than frig


Jim, chk for air diverter in wrong position
the fridge cools from freezer air flow direction control. Like a door. The more/less controls may be messed up.

May 14, 2009 | Bathtubs & Whirlpools

1 Answer

Dishwasher isnt getting water too it and stops half way through the cycle are there any filters on the machine that require cleaning?


No,No, inlet filter. Sounds like the water control solenoid is not opening or you have a hose kinked or the water turned off under the sink--Note, no intentions of insult, Just need to check everything checkable before calling in costly help. Good Luck. Thissolenoid is controlled electricaly throught the timer, so either one could be faulty.

May 06, 2009 | Bathtubs & Whirlpools

Not finding what you are looking for?
Bathtubs & Whirlpools Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bathtubs & Whirlpools Experts

Mike

Level 3 Expert

4331 Answers

Tim Whalen

Level 3 Expert

3056 Answers

john h

Level 3 Expert

7167 Answers

Are you a Bathtub and Whirlpool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...