Question about Projection Televisions

2 Answers

Received universal remote (jumbo) cable box is motorola cant get it to work please advise

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 163 Answers

Provide me model number?

Posted on Jan 01, 2009

  • ronny2051 Jan 01, 2009

    please provide the full model number of your jumbo cable box.


  • ronny2051 Jan 01, 2009

    Here are the Universal Codes & Instruction for the Sentry RMC10 Jumbo Remote: 
    http://www.megaupload.com/?d=NQH8Z0X6&nb...

    It is in PDF format, so you would need the Adobe Reader http://www.adobe.com), or other alternatives such as (the Foxit Reader, which can be obtained fromhttp://www.foxitsoftware.com) in order to open it. 

    As far as entering the code goes, it shouldn't be that hard to program if you follow the instructions. 

    A brief synopsis on how to do it is as following: 

    1. Manually turn on your device. (TV, VCR, DVD, etc...) 

    2. Press & hold the "Code Search" button until the red light stays on. Release that button once the red light stays on. 

    3. Next press the device that you are trying to program on the universal remote, i.e. TV, VCR, DVD, etc... 

    4. Enter in the first code listed. The "Code Search" red light button will turn off once your code is enter. 

    5. Now test your device to see if the code works or not. If not, repeat steps 2 through 4 all over again until you can successfully operate your device. If none of the code works, then you have to look at the instructions and follow through with what they say. 

    If that still doesn't work, then it could be that your device is not supported.


×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Projection T... Master
  • 61,168 Answers

Do u have the code's for the cable box and they don't work? if so try using the code search function of the remote, check the owner manual for instructions on this, u have to follow the instructions for both code entry ways to the letter or it will not work, Read the instructions again for both ways, with the code and code search method.

Posted on Jan 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code for sharper image jumbo tv remote to operate a motorola brand cable box. remote instructions dosn't list it and code search is not successful.


If you go to a website called www.mscustomercare.com. Scroll down to the bottom of the page click on The Sharper Image Universal Jumbo Remote then click download. The manual has the instructions and codes. Good Luck. Source(s): http://mscustomercare.com/

Jan 30, 2010 | Projection Televisions

1 Answer

Through Amazon a Brookstone's "Jumbo Universal Remote" was delivered - there is no identification of who manufactures this remote. We need to have it control an AT&T-California cable box which was...


I happen to be a Jumbo Universal remote Expert here at Fixya, so I hope I can help. It is possible that this remote just won't run your Motorola cable box, but I wouldn't give up until I had tried the codes from the list in the manual, as well as run through the auto-setup feature of the remote for CBL and for SAT, where it just tries all the cable box codes one at a time.

I was able to find a working motorola codes for an Innovage Jumbo Remote, a three digit code remote you might as well try: 051.

You have probably tried the codes for Motorola (031) and GI (000, 032) from the manual using these steps:

1. Turn on the device with which you want to use the remote control.
2. Locate a 3-digit code for your device. (000, 031 & 032 for example)
3. Press and hold the corresponding button on the remote control
(CBL) for approximately three seconds. The POWER INDICATOR illuminates.
4. Enter the 3-digit code for your device within 30 seconds. The POWER INDICATOR shuts off.
5. Press the ON /OFF button to verify correct code entry. If the device shuts off, the code was entered correctly. If the device does not shut off, repeat steps 3-4, using a different code located on the Code List.

If those are still a bust, try the GI SAT codes 018 & 019.

Have you tried the following steps with both CBL and then SAT to search it's database?

1. Turn on the device with which you want to use the remote control.
2. Press and hold the corresponding button on the remote control
(SAT or CBL) until the POWER INDICATOR on the remote control illuminates. The remote control is in programming mode.
3. Press and release ON /OFF. The POWER INDICATOR on the remote control flashes once and stays on indicating the unit is in Power Scan mode.
4. Press CHANNEL UP or CHANNEL DOWN repeatedly until the device turns off.
5. When the device turns off, press any key to store the code.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

I hope that helps.

Oct 26, 2009 | Projection Televisions

1 Answer

I have a universal remote and need the code for a Sony Videoscope XBR projection tv


I don't know if all codes are the same. Comcast Cable gave me a list of codes for their universal remote for their motorola cable boxes. For Sony tvs it says either 0000 or 0111. I still use all 7 of my remotes. Universals are basically only good for power and volume. I need the other remotes handy to enjoy the other functions of my system! Anyway, hope this works 4-u and that you get better use out of it than me.

Sep 01, 2009 | Sony KP-51HW40 51" Rear Projection...

1 Answer

Programing a universal remote


Try putting it into learning mode ...

Jan 06, 2009 | Projection Televisions

5 Answers

I am trying to find a universal remote code to control the new Zenith digital tv tuner converter box. The model # is DTT900. It is for a person with low vision who cannot see the buttons on the remote...


Hi,

Pls post back with the brand and model of the universal (replacement) Remote Control or what remote control you would want to use with the Zenith DTT900 Digital-to-Analog Converter Box.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Oct 23, 2008 | Projection Televisions

1 Answer

I lost the manual for my Innovage Jumbo Universal Remote and I need The codes for a Samsung TV, General Instrument cable receiver and an apex DVD player


You can download the manual at the following site:
http://www.remotecentral.com/cgi-bin/files/dl.cgi?file=others/innovage/jumbo-manual.zip&area=other
Had the same problem myself...

Oct 15, 2008 | Projection Televisions

12 Answers

Gfm tv universal remote code


Use the code for the sylvania tv. It worked for me!

Apr 30, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...