Question about Fitness Quest Edge 482U Upright Exercise Bike

Open Question

Error code E1

How to reset from error code E1

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I bought a Krypto bicycle lock over 5 years ago. I don't see it displayed on your website. It has yellow ends with 4 digit combination numbers red on black.The rope cable is grey and has a clear...


Krypto has the resetting of the combination lock on their website (under Maintenance) but if you cannot unlock it in the first place you can not reset the combination. You have to know the old combination to get it open.

Feb 23, 2011 | Kryptonite Bicycle Accessories

1 Answer

Check engine light came on


The check engine light comes ON when the cars computer (the ECU) notices any kind of electrical problem in car. In some cases the check engine light comes on then turns off. In that case the exact error is not getting confirmed so this happens. But once the problem gets confirmed the engine light will remain permanently ON till the problem gets solved. In this case I suggest you to get your car scanned at autozone service center. It's absolutely free. In case in car scanning, if any error code is retrieved then you can check which part is faulty as per the error code. In case if no error code is retrieved then you can continue driving, till you get any confirmed indication. ---------- This will help. Thanks. Helpmech.

Dec 09, 2010 | Mopar Chrysler Town & Country 2001-2008...

2 Answers

How do i reset the combination on my squire padlock model No. shcb65 its open thanks gary


this can only be done when unlocked, undo the small screw next to the pull-knob, only a couple of turns...you'll know when cos it will allow the knob to be pulled further out. whilst holding the knob out put your new code in then do the screw up again.

Jul 30, 2010 | Bicycle Accessories

1 Answer

After replacing the battery on my polar cs600 I got and error 16


After you replaced battery you just have to put all four buttons together to reset the cs600. Than press the middle button ok and it should start normal.

Oct 19, 2009 | Polar CS600

3 Answers

I lost the instructions and don't know how to unlock using "original code" and how to create a new code


try all zeros Kryptonite locks come preset to zeros once unlocked there is a small lever inside were it locks together pull it down and set your new combo then push it back up

Oct 17, 2009 | Kryptonite Kryptoflex 1218 Combo Cable...

1 Answer

How do i reset the code on my jeep bike lock


you may need to do trial and error method to find jeep code.
say
111
113
113
114

.
.
.
.
.
121
123
124
125
126
127
.
.
.
211
212
213
214

.
.
.
.
. etc.
you will find code.

Sep 11, 2009 | Bicycle Accessories

6 Answers

Lost manual to Bell wireless bicycle computer


Here are some things the book doesn't tell you:
You have to completely reset the speedometer and lose your odometer to reset the MPH. Hold both buttons for 3 secs to get reset. (Remember to use the left button to walk through the setup process and use the right button to change the settings.) First set the wheel size using Ideluna's settings above on this page (right button to change the setting and left button to go to next number). Next is MPH/KPH, after wheel size setting, push left button again and km flashes. Push right button to change the setting to MI. Next is TIME. Push left button and you'll see the time. Hold down left button till 24hr appears. Push right button to change to 12hr. Then push left button to go to flashing hour. Change with right button. Then left button to go to flashing minute. Right button to change minute, hold down to change minutes fast. Now you are set up. Now the process changes, use the right button to walk through the menu and use the left button to reset. Don't push both buttons anymore unless you want to reset everything again. If you want to reset something just hold the left button down until 0. When you are in SCAN mode, push the right button to go to Time, To go back to SCAN once, hold the right button down - It will scan everything once and return to TIME. To go to ODO, push right button once, push again for DST, push again for MXS, push again for AVS, push again for TM, push again for SCAN to stay in SCAN.

Mar 24, 2009 | Bicycle Accessories

Not finding what you are looking for?
Fitness Quest Edge 482U Upright Exercise Bike Logo

Related Topics:

770 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fitness Quest Bicycle Accessories Experts

Carl Marquardt
Carl Marquardt

Level 1 Expert

29 Answers

John Egan
John Egan

Level 2 Expert

72 Answers

ebike

Level 1 Expert

23 Answers

Are you a Fitness Quest Bicycle Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...