Question about Kuppersbusch K 24 in. IGVS 669.1 Built-in Dishwasher

1 Answer

The digital display is showing S2

The diswasher is igv 699.
It is displaying S2 and will not respond when i press menu or start keys?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Try switching off the power for a short time it might reset itself

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model ESL 499. Why doesn't it start?


You have activated the delayed start function. Please read following instruction from user manual.

8. Delayed Start button

Allows the start of the programme to be delayed by a minimum of 1 hour, up to 9 hours. How to set the delayed start When the button is pressed, the number appears in the display (4). Press the button again to select the number of hours by which you wish to delay the programme start, up to a maximum of 9. E.g.: if you have selected number , the wash programme will start in 2 hours' time. To cancel the delayed start set, press the button until the number appears. Close the dishwasher door to start the countdown: a long audible signal (about one second) informs you that the function is active. If you open the door again you will see, in the display (4), how long there is to go (in hours) before the programme starts. A flashing dot in the digital display means that the delayed start function has been activated. Opening the door has no effect on a countdown which has already been started. If, during the countdown, you wish to see the programme number selected in the display, press the Programme Selector button (5). If, after having started the countdown by closing the dishwasher door, you wish to cancel the delayed start, press button (9) (Cancel) for about 2 seconds until the short «instruction accepted «signal is heard».

Dado

Sep 16, 2015 | Electrolux Dishwashers

1 Answer

Bosch dishwasher has a buzzer on all the time .


I'm not sure if you mean it is buzzing because of a fault or if it buzzes to say the program has ended and you want to switch this off??? if it is the later the following should help


To activate any of the Dishwasher Options listed, follow these steps:

Open the dishwasher door far 1. enough to expose the control panel.

2. Press the On/Off button.

3. Press the MENU/OK button until the desired option appears in the display window.

4. Press the - or + button to step through the available option settings.

5. When the desired setting is shown in the display window, press the MENU/OK button to save the setting. The display will indicate "Value Stored" and return to the main

menu. If you did not change the setting, press the start button to return to the main

menu.

6. Select the desired wash cycle by pressing the - or + buttons.

7. Press the start button and close the dishwasher door to begin the cycle.

NOTE: In the Options Step Down Menu, you can return to the main menu at any time by

pressing the START button.

Feb 20, 2013 | Bosch SHX98M0 24 in. Built-in Dishwasher

1 Answer

Will not run no lights or anything


Hello,

The most probable thing wrong is going to be a blown fuse on the control panel. To check for that, disconnect power to dishwasher by turning off circuit breaker ,remove torx headed screws from around the inner door,seperate inner/outer door panel,remove the plastic cover off of the control panel, and use a multimeter set to measure ohms and remove the 2 wires to the thermal fuse and check for continuty with ZERO ohms resistiance on the thermal fuse. IF the fuse is blown the meter display will show OL or the display will not change...if using a meter with a needle the needle will not move if the fuse is blown..if the fuse is good the display will show 0.00-1.00 on a digital meter and the needle will swing all the way to the right and stay there on analog meter. If the fuse does check to be good the most likely cause of the diswasher not running will be the door switches. Here is what the fuse looks likeoldtech2332_88.jpg

Good luck i hope i helped you to fix your dishwahser,
GENE

Sep 04, 2011 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

What doe error code CE signify????????..


4. Troubleshooting

4-2

4-2. Service Inspection Mode

- Press the Delay Start + Normal + Power keys at the same time for two seconds to enter Service Inspection Mode.

- "ALL" is displayed for the first three (3) seconds and then "t1" is displayed.

- You can change the mode by pressing the Normal key. Each time the Normal key is pressed, the mode changes in the order of t1 ? t2 ? t3 ? t4 ? t5 ? t6 ? t7 ? t8.

- If you want to activate a mode while operating the dishwasher, the door must be closed (The Door switches are ON.)

- If an "oE", "LE" or "tE1" error occur, make sure to enter Service Inspection Mode after resolving it.

- Service Inspection Mode is described in the following table.

Mode Related parts Symptoms Note

t1

Inlet Valve

Flow Meter

Low Level Sensor

4E

9E

If you press the Delay Start key, water is drained for 45 seconds and then the water supply starts.

If the pulse count is more than 660, change the mode.

Make sure to change the mode when the pulse count is more than 660 in t1 mode.

t2 Circulation Motor A nozzle does not inject

water.

1. Press the Delay Start key to start or stop the Circulation Motor.

2. If a low water level is detected, water is supplied again and the operation continues.

t3

Circulation Motor

Heater

Thermistor

HE

1. Press the Delay Start key to start or stop the heater and the circulation Motor.

2. If a low water level is sensed, water is supplied again and the operation continues.

3. The current temperature is shown on the display.

4. If the water temperature is more than 70?C, the Heater does not operate.

t4 Fan Motor The Fan Motor does not

operate. Press the Delay Start key to start or stop the Fan Motor.

t5 Drain Pump

Low Level Sensor 5E 1. Press the Delay Start key to start the 2 parts.

2. When draining is finished, "t5" is blinking on the Display LED.

t6 Low Level Sensor

When the Micro Switch

is turned on/off, there is

no change on the display

or a symbol other than

On/OFF is displayed.

1. MICRO SWITCH On

? The sensing state is displayed as 'On' on the 88 segment display.

2. MICRO SWITCH Off

? The sensing state is displayed as 'OFF' on the 88 segment display.

t7 Thermistor There is no change in the

water temperature. The current temperature is displayed.

t8

Half Load Position of

Distributor Motor

Micro Switch

(DMR77 Model)

PE

1. If you press the Delay Start key, the parts operate just once.

2. There is no stop function.

3. While the Distributor Motor is operating, its sensing state is displayed as On/OFF on the 88 segment display.

4. When the Distributor Motor stops, the sensing state (On/OFF) of the Micro Switch is displayed.

Caution

If it has the power problem, you must check the FUSE first.
This dishwasher has the FUSE upon the Base. Refer to the 4-10 page.
Try these steps to solve your error there is no CE code listed in the manual

Dec 12, 2010 | Samsung DMR78AHS Builtin Dishwasher

1 Answer

I am getting a CE error, what does that mean? Bill


4. Troubleshooting

4-2

4-2. Service Inspection Mode

- Press the Delay Start + Normal + Power keys at the same time for two seconds to enter Service Inspection Mode.

- "ALL" is displayed for the first three (3) seconds and then "t1" is displayed.

- You can change the mode by pressing the Normal key. Each time the Normal key is pressed, the mode changes in the order of t1 → t2 → t3 → t4 → t5 → t6 → t7 → t8.

- If you want to activate a mode while operating the dishwasher, the door must be closed (The Door switches are ON.)

- If an "oE", "LE" or "tE1" error occur, make sure to enter Service Inspection Mode after resolving it.

- Service Inspection Mode is described in the following table.

Mode Related parts Symptoms Note

t1

Inlet Valve

Flow Meter

Low Level Sensor

4E

9E

If you press the Delay Start key, water is drained for 45 seconds and then the water supply starts.

If the pulse count is more than 660, change the mode.

Make sure to change the mode when the pulse count is more than 660 in t1 mode.

t2 Circulation Motor A nozzle does not inject

water.

1. Press the Delay Start key to start or stop the Circulation Motor.

2. If a low water level is detected, water is supplied again and the operation continues.

t3

Circulation Motor

Heater

Thermistor

HE

1. Press the Delay Start key to start or stop the heater and the circulation Motor.

2. If a low water level is sensed, water is supplied again and the operation continues.

3. The current temperature is shown on the display.

4. If the water temperature is more than 70ºC, the Heater does not operate.

t4 Fan Motor The Fan Motor does not

operate. Press the Delay Start key to start or stop the Fan Motor.

t5 Drain Pump

Low Level Sensor 5E 1. Press the Delay Start key to start the 2 parts.

2. When draining is finished, "t5" is blinking on the Display LED.

t6 Low Level Sensor

When the Micro Switch

is turned on/off, there is

no change on the display

or a symbol other than

On/OFF is displayed.

1. MICRO SWITCH On

→ The sensing state is displayed as 'On' on the 88 segment display.

2. MICRO SWITCH Off

→ The sensing state is displayed as 'OFF' on the 88 segment display.

t7 Thermistor There is no change in the

water temperature. The current temperature is displayed.

t8

Half Load Position of

Distributor Motor

Micro Switch

(DMR77 Model)

PE

1. If you press the Delay Start key, the parts operate just once.

2. There is no stop function.

3. While the Distributor Motor is operating, its sensing state is displayed as On/OFF on the 88 segment display.

4. When the Distributor Motor stops, the sensing state (On/OFF) of the Micro Switch is displayed.

Caution

If it has the power problem, you must check the FUSE first.
This dishwasher has the FUSE upon the Base. Refer to the 4-10 page.TRY THESE STEPS AND SEE WHAT HAPPENS THERE IS NO CE FAULT CODE LISTED IN THE MANUAL

Dec 12, 2010 | Samsung DMR78AHS Builtin Dishwasher

1 Answer

Water won't drain


Do the diagnostic test:
SHU 53 MODELS

To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show “88′ when REGULAR WASH button is pressed and “8h” when Delay Start button is pressed.
To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4).
0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
1 = Aqua Sensor (“Sensotronic”) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), display will show fault code “4′ and unit will continually fill and drain where testing won’t be completed. If flow switch (e5) has failed (opened), display will show “0′, water won’t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code “8′ immediately and testing will end shortly after water has started circulating.
---------
The dishwasher not draining is most probably faulty drain pump or drain hose is got bit loose.It has to be checked and confirmed
.You can get required parts from www.repairclinic.com
Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Aug 27, 2010 | Bosch 24 in. SHU53 Built-in Dishwasher

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to...


SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Aug 01, 2009 | Bosch SHU5315UC Dishwasher

1 Answer

Bosch SHU 6800 Water hot at sink only luke warm at the washer


BAD CONTROL BOARD TO TEST TO SEE IF THIS IS THE ISSUE RUN TEST PROGRAM
To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by
pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ “20” = version 0 without jumper). When
wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and
REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display
alone). Cycle Countdown display will show "88" when REGULAR WASH button is pressed and "8h" when Delay Start
button is pressed.
To start testing, press both SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended,
Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added
together, (e.g./ “6” = faults 2 + 4).
0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault
1 = Aqua Sensor ("Sensotronic") fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil,
measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays
at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
If water level switch (f1) has failed (opened), display will show fault code "4" and unit will continually fill and drain where
testing won't be completed. If flow switch (e5) has failed (opened), display will show "0", water won't heat (to 150ºF) and
water won’t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code "8" immediately and
testing will end shortly after water has started circulating

Jul 18, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

3 Answers

Bosch


f is fill fault to much or not enough water or water in the sump white plastic base the f code will not go away until you solve the problem when the f code shows up the drain motor will run all of the time

Apr 01, 2006 | Bosch 24 in. SHU6802UC / SHU6806UC...

Not finding what you are looking for?
Kuppersbusch K 24 in. IGVS 669.1 Built-in Dishwasher Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kuppersbusch Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Kuppersbusch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...