Question about Equator EZ 2512 CEE Front Load Washer / Dryer

1 Answer

Equator ez2512 washer dryer keeps throwing the main belt off.

The machine runs fine with no load in it , but as soon as I add clothes the belt falls off on the fast spin. The belt looks fine. it is a serpentine belt and I am wondering if there should be grooves on the pully?? I had a repair man out to the house after running and replacing the belt several times and he told me that I did not know how to put the belt on. Of course the belt fell off 1/2 hour after the man left.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 311 Answers

Somthing is going to be obvious there.you have to inspect it whatch it while it runs

Posted on Dec 31, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore 417.43142200 final spin is slow


obviously the timers contacts are bad so replace the timer.

May 16, 2017 | Kenmore 43142 Front Load Washer

1 Answer

Maytag HAV2460AWW struggling to spin and drain


Gently tilt machine backwards and look underneath for stretched or damaged drive belt.The drive belt also runs pump. If it is slipping under load then the machine will not spin at full speed and pump out the wtare correctly, thuis leaving some in the machine at the end of the cycle.

Sep 07, 2012 | Washing Machines

2 Answers

Bosch washer won't spin with wet clothes


I am not sure if Bosch has a "load sensing" sensor, but I would start there else you may have a motor issue, or bad capacitor on your motor.

Aug 03, 2012 | Bosch Nexxt 500 WFMC3301 Front Load Washer

1 Answer

Zanussi fs1455w not spinning fast under load. Without anything in the drum it spins fine??? Tried all speeds with the same result. Any ideas???


May be not pumping efficently. when the spin starts the initial rush of water floods into the drum from the clothes a build up of water under the drum causes a braking action on the drum and slow spin speed.. look for partial blockage in pump chamber hoses or under sink if a spigot connection. probably not the belt as it would throw off a loose belt. Check it anyway. if non of these check carbon brushes they may on the verge of failure.

Jul 23, 2010 | Zanussi FS1455W Front Load Washer

1 Answer

Cloths Soaked after Spin Cycle


If the motor has a transmission, it could be stuck in 1st gear. I think the agitator running is normal.

Jan 17, 2009 | LG WM1814CW Front Load Washer

2 Answers

Clothes still wet at end of spin cycle


i would check your belt.the added stress of a full tub longer with water may have done it in.part#wh1x2026 God bless,tom

Jan 10, 2009 | GE WBSR3140DW Top Load Washer

1 Answer

Washer will not spin sometimes


look under for the belt(s). Belts must be clean and dry, and in good shape, no oil or grease on them. If the machine is leaking on the belt, it will slip. Detergent will make the belt slip.

Apr 01, 2008 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Maytag atlantis washer


I am also expiriencing the same situation.
I took a look at the machine and it appears to be in good working order.
But the belt does appear to be in need of replacing. I have ordered one and should find out everything will be back to normal once it is installed.
The worn belt would explain a lot.
- Light load are fine due to the lack of power needed to spin the contents.
- Heavy loads need the maximum amount of power it can get to spin.
But does not because the belt is slipping further into pulley grooves and is probably partially slipping, due to the wear.

Dec 02, 2007 | Maytag Atlantis MAV6000 Top Load Washer

Not finding what you are looking for?
Equator EZ 2512 CEE Front Load Washer / Dryer Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Equator Washing Machines Experts

Heartland Ho

Level 1 Expert

24 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Brad Brown

Level 3 Expert

16447 Answers

Are you an Equator Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...