Question about Hoover HTC243 Top Load Washer

4 Answers

Hoover washing machine top load, model 550m.5.5kg

Doesnt stop filling with water.doesnt change cycle or spin.water leaks from cold water hose.

Posted by on

  • 11 more comments 
  • bilby 12 Jan 28, 2009

    Same problem.Machine doesnt stop filling with water. Pressure stat is ok.Someone have to blow air into pressure stat vacuum hose ,all the time to stop taking water and start wash cycle. When I blow air down into air chamber I can hear water bubbling. Is it normal? Hoses are ok. How to clean air chamber please?

  • havaprob May 18, 2009

    My washing takes forever to fill with cold water. Please advise how to fix it

  • Anonymous Mar 15, 2014

    fills with water but does not wash. it will only spin

  • Anonymous Mar 15, 2014

    fills with water but will not wash ..only spins

  • Anonymous Mar 19, 2014

    Hoover top load 500mb washer, fills with water and then dosent complete cycle of wash?

  • Anonymous Mar 19, 2014

    Dosent finish its cycle, fills with water and that's it?

  • Anonymous Mar 21, 2014

    Machine continues to run and doesnt stop at end of cycle

  • Anonymous Mar 21, 2014

    The cold water is supplied via a rainwater tank and is pumped into the laundry and there is plenty of pressure.

  • Anonymous Mar 21, 2014

    lg wft8501tp machine stops after one cycle. Water doesnt drain

  • Anonymous Mar 21, 2014

    when I turn on the washing machine the water will not turn off and flooded my living room. Its not the supply hoses. when I turn it off the water stops

  • Anonymous Mar 23, 2014

    My machine wont fill it is fitted with a partial aqua stop could i change it for a normal hose thanks

  • Anonymous Mar 26, 2014

    stopping in between cycle

  • Anonymous Mar 31, 2014

    The machine fills up normally but then the wash cycle won't start, it just clicks. But the spin cycle works normally

×

Ad

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,462 Answers

Water leak from cold hose nothing to do with other problem. tighten hose connection and fit a new hose washer overfilling probably because air chamber blocked. remove lid. you will see a pressurestat somewhere at the top - usually round with anything from 3 to 7 wires and a small tube underneath. follow hose down and it connects to the air chamber. make sure this is free of gung and check hose for splits and has no blockage. to check the pressure stat itself, attach your own hose to the stat and while machine in fill mode, blow down this hose and you should hear a click and water intake will stop

Posted on May 04, 2007

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Very simple fix, you open the top panel, then you can see the water inlet solenoid valve, which may not be insert deep to the bottom part after the machine move, just push the inlet valve down 1/2 cm, it will stop the water leak

Posted on Dec 02, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My cold tap leaks water from top when I use machine fittings are good just moved to new premises could this have upset works

Posted on Nov 25, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Part No: 47841-405 hoover washing machine

Posted on Aug 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 21882 top load Kenmore washer will start the cycle but stops after filling up; i can restart the cycle by pushing the knob in and going a little further in the cycle then starting again. But after a...


When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
  • Jan 29, 2011 | Kenmore 24032\24036 Top Load Washer

    1 Answer

    My washing machine is a Roper top load washer. The problem I am having is that the pump from the cold water drain from under the washing machine. Do I need another pump? The hot water will work. I use the...


    This model is a direct drive with only one pump, the drain pump. If the drain pump leaks, which is a common problem on these models, it will leak no matter what temperature wash is selected! If you a have a leak on cold, it will probably also leak on warm wash. Your problem is your solenoid operated fill valve on the cold side. Only one fill hose comes off of this combination fill valve to your fill plenum at the top back of your tub. So if it leaks on the cold, but not hot, check for a crack in the plastic housing of the valve on the cold half. The valve is located on the inside back of the machine on top right when looking at the front of the machine. They are fairly inexpensive and easy to replace.

    Hope this helps

    kcomp1863

    Jan 18, 2011 | Roper RAS6233KQ Top Load Washer

    1 Answer

    Hoover 550M washing machine - taking ages to fill, water is just dribbling out. Was fine when started, lifted lid to put in clothes and now only dribbling out. Water pressure in rest of house seems to be...


    Check the inlet screen on the hose connection on the back of the machine. This may be clogged with debris, also make sure you hose is not crimped. You can unhook the inlet hose and put it in a bucket and turn it on to see how much water is actuall coming thru that hose. I suspect some type of blockage in the inlet.

    Nov 11, 2010 | Hoover HTC243 Top Load Washer

    1 Answer

    I have a top loading Kenmore Washing Machine. I don´t have the excat model but looks like a KENMORE HEAVY DUTY SERIES 70 AUTOMATIC WASHER, MODEL # 110.92273100. The problem presents after finishing...


    You may have 2 defective parts.
    First,make sure the hot and cold water hoses are connected correctly and both turned on.
    If the water fill problem is the same,the water temp switch is bad.
    The not filling after the wash cycle could be a bad lid switch.
    Set the machine for SPIN and turn it on.
    If it does not spin,replace the lid switch.

    Sep 20, 2010 | Kenmore 24042 Top Load Washer

    1 Answer

    Washer stopped at the drain cycle Model LSR8233JQ1


    Could be either a bad lid switch or a bad water valve.
    Set the timer dial to SPIN and turn the machine on.
    If it spins the lid switch is OK. If it does not spin the lid switch must be replaced.
    Next,set the timer dial on a wash cycle and set the water temperature knob to COLD water. If it fills,the lid switch is bad. If it does not fill the water valve is bad or the cold screen filter is clogged.
    If the COLD does not fill,turn off the cold water faucet. Remove the cold water hose from the machine water valve and check for a clooged screen.
    If it does not fill with COLD water and the screen is clear,replace the water valve.

    Oct 27, 2009 | Whirlpool LSR5132PQ Top Load Washer

    1 Answer

    Blocked filters/dodgy pump?


    The problem you are having could simply be the inlet valve.

    The inlet hose is attached to the inlet valve on the machine. Where it screws on that is.

    You can get a valve from an appliance parts shop and they are inexpensive.

    Jun 18, 2009 | Hoover HTC243 Top Load Washer

    1 Answer

    Kenmore front-load washer stops at rinse cycle


    When the washer initially fills for the wash, is it only hot water entering the drum? Try switching the water temperature between hot and cold as it fills. If any of them show little or no water getting through, it sounds too easy but check to make sure water supply taps are on, and that the cold/hot fill hoses aren't reversed. Remove the fill hoses and check any of the screen filters for blockage (in the hoses and in the inlet water valve). When the machine stops and waits to fill but all you hear is a hum, it sounds like there is power going to the valve but water is not able to get through it.
    Good luck!

    Mar 03, 2009 | Kenmore 43142 Front Load Washer

    1 Answer

    Cold water will not shut off at end of spin cycle


    electriic inlet valve is obstructed, try removing cold water hose direct the hose into a bucket and fill the tub on the warm setting (flushing the cold valve) then try the washer again ..If that doesn't work a new valve is needed

    Dec 25, 2008 | Maytag Neptune FAV6800AW Top Load Washer

    2 Answers

    Does Not Rinse


    Check each temperature during initial wash fill. Set to hot water, is hot water coming out? Set to cold water, is cold water coming out? The rinse cycle is cold only. If cold water is not working machine will just stop at rinse.

    If cold water not working:
    Disconnect cold water hose from machine. Inspect the filter screen on the cold water connection. DO NOT REMOVE SCREEN. If full of debris, use a spray bottle with a hard spray to remove debris. If unable to remove or cold is still not working, replace valve.

    Jun 14, 2008 | Whirlpool LSR6332K Top Load Washer

    Not finding what you are looking for?
    Hoover HTC243 Top Load Washer Logo

    1,755 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hoover Washing Machines Experts

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    Gerry Harvey
    Gerry Harvey

    Level 3 Expert

    1474 Answers

    shaun taylor

    Level 3 Expert

    1527 Answers

    Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...