Question about Kenmore 24032\24036 Top Load Washer

1 Answer

Tub bearing kenmore front loader

I'm an auto mechanic think i could do this bearing??? how would i check it....???? thanks kevin

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

You have to change the whole outer tub that is the only way you can get but take off your top by taking the screws out of the back and then it slides back then see if the noise is coming from the back center of the tub if so if will need to be changed and the tub is expensive

Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Replacing a Rear Tub Bearing


Rear Tub Bearing Replacement
(Part 1 of 3)

This advice is for replacing the rear wash tub shell of most Kenmore Elite HE model FRONT LOADERS, along with Whirlpool Duet, and some Frigidaire FRONT LOADER models. This is a repair that would be rated as difficult due to the extensive disassembly and reassembly of components.

The requirement to replace the rear wash tub shell is usually attributed to the rear tub bearing failure in which the bearings are molded into the tub and cannot be replaced otherwise. In some situations the replacement of the inner spinner basket (stainless steel tub) may also be required due to the corrosion and breakage of the spider arms in the back of the basket that support the basket.

SYMPTOMS: Washer exhibits excessively loud “rumbling” type noise during the spin cycle, excessively vibrates, or won’t spin at all.

DETERMINING IF THE BEARING AND SPIN BASKET ARE BAD: With the washer door open, place your hand inside the basket and push straight up. If there is excessive play in the tub (wobbles up and down) the bearing is probably bad. If the spinner basket scrapes against the outer tub shell when you give it a spin, you will have to replace the inner spin basket as well. Unfortunately, you cannot see the condition of spinner basket supports until it is removed from the outer tub shells. In some cases, a brownish colored stain my show up on clothing as the bearing seal has been breached and leaks into the spinner basket.

Before starting this repair, make sure you read through all instructions thoroughly and place the washer is in an area that gives you plenty of space to work.

(cont’d)

on Jul 07, 2008 | Kenmore Elite 45986 Front Load Washer

1 Answer

My Kenmore Front Loader washer machine is making a loud noise during the spin cycle


tub bearing more than likely.tub has a 10 yr warranty so call sears get the flat rate labor charge their offering then have them replace the tub

Jan 11, 2010 | Kenmore 43042 Front Load Washer

1 Answer

How do I remove the back panel off Kenmore Elite Dryer


Overfilling loads can cause small objects like pins, coins, and small socks to get between the tub abd Basket of your washer.

The basket is held onto the rear half of the outer tub simply by the bolt to the main pulley.
Remove the bolt, remove the pulley, and the basket shaft should slip right out of the bearings of
the rear tub.

Simply shining a light around between the basket and outer tub should confirm that there is something in there, since you have access to do this with
the front tub removed. Go ahead, remove the pulley and bolt, and if
the basket comes out, then check everything out.

If it doesn't, don't try pounding it out; stop there and go to plan B, which is a new basket
and tub assembly.

Front - loader: Remove Bellow

http://media.fotki.com/1_p,wbwdbgtqbsqkfbgxgtqsskgwtqkq,vi/kdtfgttdqxkfqrdrrdq/1/1303472/5961857/image45926img-or.jpg



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 26, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

My washer post f 32, i think it need to be cleaned, but


Overfilling loads can cause small objects like pins, coins, and small socks to get between the tub abd Basket of your washer.

The basket is held onto the rear half of the outer tub simply by the bolt to the main pulley.
Remove the bolt, remove the pulley, and the basket shaft should slip right out of the bearings of
the rear tub.

Simply shining a light around between the basket and outer tub should confirm that there is something in there, since you have access to do this with
the front tub removed. Go ahead, remove the pulley and bolt, and if
the basket comes out, then check everything out.

If it doesn't, don't try pounding it out; stop there and go to plan B, which is a new basket
and tub assembly.

Front - loader: Remove Bellow
http://media.fotki.com/1_p,wbwdbgtqbsqkfbgxgtqsskgwtqkq,vi/kdtfgttdqxkfqrdrrdq/1/1303472/5961857/image45926img-or.jpg



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Apr 11, 2009 | Kenmore 43142 Front Load Washer

1 Answer

My kenmore front loader makes a knocking when it spins.


how old?sounds like the bearing are going bad,on yours the tub and bearing are one unit,so you have to change out the whole thing-mike

Mar 24, 2009 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Kenmore 24032\24036 Top Load Washer Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...