Question about Remote Controls

3 Answers

I have a OnkyocTX-SR606 AV receiver that requires me to push the "tuner" button before I can turn the unit on or off with the "on standby" button. How do I get my harmony one to recognize this?

Posted by on

  • 1 more comment 
  • strachan_ken Dec 31, 2008

    Will this code appear in the Onkyo manuel?

  • strachan_ken Dec 31, 2008

    will the code appear in the Onkyo manuel or the harmony one manuel?

  • strachan_ken Dec 31, 2008

    There is no such information in the maneul

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Contributor
  • 1,199 Answers

Did you try random acess codes ?

Posted on Jan 01, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 326 Answers

U will find the code in harmony one manual.

Posted on Dec 31, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 142 Answers

There should be some sort of sync code provided in the manual or instructions with details on how to set everything up.

Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does it turn on sporadically, stay on briefly, then turn off?


Sounds like a defect to me return it for a working model.

Jun 01, 2015 | Sherwood RX-4105 2-CHANNEL...

1 Answer

My pioneer sx-316 multi channel receiver is off on protected mode what do I do to restart


I read the instructions perhaps slightly differently perhaps. I take the instructions to mean first hold down tone and then hold standby/on key for three seconds. Have you tried doing it as two steps?

1 Switch the receiver into standby.
2 While holding down the TONE button, press and hold the  STANDBY/ON button for about three seconds.
3 When you see 'RESET?' appear in the display, press the ENTER button. OK? shows in the display.
4 Press SETUP to confirm.

Feb 03, 2015 | Pioneer New Original SX316S Remote Control

1 Answer

My 16" led lcd dvd combo TVs does not turn on. The standby light indication is on but when I push the standby button on the TVs unit nothing happens. As I have lost the controller and un able to switc


Fault with its main board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Jan 05, 2015 | Remote Controls

1 Answer

Won't go to tuner


If the set's input is selected to AV, it will skip tuner. Check whether its the reason. Check its input selection first. If it is set to AV; set it to TV. Gopakumar Gopalan Google

Mar 19, 2014 | Remote Controls

1 Answer

TV won't turn on. Red standby light blinks


Samsung told me this was a common problem and I would have to have it serviced by an authorized repair facility.
My problem ended up being the internal power supply, but they also told me the main boards burn up.

Nov 06, 2013 | Samsung BN94-05038F Main Board for...

1 Answer

Hahnel Giga T Pro II remote function not working


Hi Jack,
I assume you have an answer by now but if not. Cable between receiver and camera is the issue. One of the jacks has 3 black rings on it, which must go into the receiver. The other has 2 black rings and goes into the camera.

regards
Kent

Mar 27, 2013 | Hahnel Giga T Pro Ii Wireless Remote...

1 Answer

Remotes working sporatically


Your description suggests bad/dirty contacts inside the remotes and jammed volume buttons on one of them. Cleaning the rubber pads and the circuit boards on all of the remotes might solve the problem.
Use some ethyl or isopropyl alcohol and cottonwool to clean them.

By the way, here's a nice way to test a remote using your mobile phone's camera:

Turn the camera on, point the remote towards the camera lens so you can see it on the mobile's display.

Look at the display on your mobile phone and press buttons on your remote - you should see bluish/greenish flashes from your remote's emmiter each time you press a button on the remote (the camera on your mobile shows infrared light from the remote as visible light on the display - if it doesn't do so in the normal mode, try the night mode for the camera instead).

If you press a button and there are no flashes, that button probably has a bad/dirty contact.

if the remote is making flashes even when the buttons are released, this means that a button is jammed (you need to clean the rubber pads and the housing, especially the holes where the buttons come through as there's probably some dirt that keeps the button pressed in, which causes the volume to go up/down all by itself).

hope this helps...

regards

3rq8 (Triarcuate)

Jul 21, 2009 | Samsung TV Remote Control

1 Answer

Don't have manual...don't know how to use some buttons


My guess on surf is it might scan channels for you. PIP is short for picture in picture and may require a second device with a seperate tuner. SWAP works with PIP button and switches (or swaps) between the pictures. FREEZE probably "freezes" picture until you push button again.

May 14, 2008 | Zenith MBR3447 Remote Control

1 Answer

RM-AV2100


Either the channel up and down buttons have both broken (unlikely) or everything else is working except the remote is not telling the device you are controlling to change the channel up or down.

Since all the other buttons are working well, that also requires that the receiving end of the pair to be working well, thus ruling out problems on that end.

Solution: Reprogram your remote to support the appropriate channel up/down codes for your TV/Tuner in question.

Dec 14, 2007 | Sony RM-AV2100 LCD Touchscreen Remote...

Not finding what you are looking for?
Remote Controls Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Remote Controls Experts

The Knight
The Knight

Level 3 Expert

68323 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4758 Answers

Are you a Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...