Question about Siemens WFXD5200UC Front Load Washer

1 Answer

How do i check if the motor or brushes are working on my washing machine

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The motor brushes were worn a visit to the domestic appliance centre to get 2 brushes at 19.99 saved a replacement motor.

all working fine now.

thanks

Posted on Jan 03, 2009

6 Suggested Answers

  • 8 Answers

SOURCE: remove carbon brushes from bosch washing machine

bad news im affraid mackem , depending on what motor your bosch has there is no way to change the carbons without removing the motor .

Posted on Feb 25, 2008

  • 1462 Answers

SOURCE: My bosch washing machine wfo2865

remove back panel.remove motor wiring undo two bolts in front. remove belt. motor will pull out.
my experience of these is that often the commutator is damaged hence brushes worn

Posted on Aug 07, 2008

  • 68 Answers

SOURCE: motor not running in Asko 10504 washing machine

The motor might have burned out. Another possibility would be a partially fried control board.

Posted on Jan 17, 2009

  • 44 Answers

SOURCE: I can't locate brushes on Bosch Logixx 1600 wasshing machine

hi

usally the brushes are at the back of the motor but depending on motor they could be inside . to get to these you need to remove the 4 screws wich hold motor together. but 1st thing to check is to look at armitor on motor and see if you can see a line going round in the middle. if there is the motor will probley need to be replaced as the motor will have burnt out. but motors are very expensive o these machines. hope this helps

regards dan

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: beko wma 510 w washing

new pump washing machine will not spin or empty. what could be the problem

Posted on May 20, 2009

  • 1 Answer

SOURCE: bosch exxcel 1200 express washing

I had F63 on Bosch washing machine (Maxx 7). I waited 5 days for a repairman and all he did was reset the washing machine processor, like this: 1. Turn the program knob to 6 o'clock 2. Hold the RPM button 3. While the RPM button is held, turn the program knob 1 click clockwise (to Rinse) 4. Release the RPM button.
This is similar to F21 which also happened to my machine. Apparently both errors are related to power surge/power cut.

Posted on Nov 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where to get new motor Carbon brushes error f06


Have you already removed the motor and dismantled it to check the brushes. It is unusual to find a universal motor (that uses brushes) in a washing machine. Normally they use an induction motor that does not have brushes.

May 25, 2016 | Washing Machines

1 Answer

How do I change the brushes on my washing machine?


Hi Shirley

Well, If you are talking about the brushes (electrical brushes) which are inside the main drive electric motor.?
Then firstly I would check to see if this motor has brushes.
Most AC motors don't use brushes on a copper commutator.
Electric motor Wikipedia the free encyclopedia
They do however use a large external capacitor to kick start them in a particular direction and these can go bad.
AC motor Wikipedia the free encyclopedia
They often sit there & hum and can be push started. Not with the fingers or hand. A wood stick on the belt drive. But thats just to prove that it will work when the Cap is replaced.
This is better done on a work bench.
motor start capacitor
But... if you know that the motor has internal brushes you still have to take the motor out & pull the back end off to see & change the brushes.
So, either way, you will have to get access to the machine to remove the motor. While there check for a tin can attached close to the motor (the Capacitor)
Usually a job for an Electrician so be careful to disconnect from the power before opening the machine. Water & Electricity can be deadly.

Good Luck
Cheers

Aug 29, 2015 | Beko Washing Machines

2 Answers

My washer wont spin


Hi if your Beko WME7247W washing machine wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor more Beko WME7247W test videos at site

Aug 08, 2014 | Beko WME7247W Washing Machine

1 Answer

How to locate the washing machine brushes?


Some motors do not have carbon Brushes as its a induction motor as a opposed to a reaction motor which does have, not sure about your model but you could check this first, if it does have a brush kit fitted they should be easy to identify and remove if on the other hand no brushes then you would need to fit a new motor. On the bosch the brushes can be hidden look at the back of the motor ,you will see two wires one for each brush connected. Good luck.

Jun 03, 2014 | Bosch Nexxt Premium WFMC6400UC Front Load...

2 Answers

My washing machine wont spin


Hi if your Beko Wm & Wma Models washing machine wont drain or has a spin problem then you have to check the carbon brushes first.

Also check all waste pipes are clear and inspect the pump I have included this video below.

At our website I am doing self diagnostic videos on these beko's as we speak so all tutorials will be in this link below
How to replace Beko Washing Machine Motor Carbon Brushes
you might find this test video helpful but only do it if you have checked the motor

Apr 12, 2014 | Beko Wm & Wma Models Washing Machine Motor...

1 Answer

Replaced beko motor brushes on washing machine and they are making funny noise


Please remove and reset the brushes are it could be out of alignment , Please check this link for tips: Brush setting

Feb 01, 2013 | Washing Machines

1 Answer

Washing machine


UNPLUG THE MACHINE BEFORE CHECKING!

It is Usually the Brushes on the Motor that cause the problem. The Brushes DO wear out on all Brush Motor washing machines eventually. How quick depends on USE and Manufacturer.

In my experience Most Bosch Brushes last between 3 - 8 years before requiring renewal. You will need to remove the brushes to check how much carbon is remaining.

Replacement Brushes are available. It would help if you provided your E.NR ( number ) which you will find on a label on the inside of the Door.

Mar 16, 2008 | Washing Machines

Not finding what you are looking for?

Open Questions:

See all Siemens WFXD5200UC Front Load Washer Questions

Siemens WFXD5200UC Front Load Washer Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Siemens Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...