Question about Konica Minolta DiALTA Di200 Copier

1 Answer

Our Di1610fp seems to be restarting continuously and we think it went aon all night. We are unable to print from our PC to it.

Posted by on

  • linda_quinon Dec 31, 2008

    We got it taken care of, thank you - I thought I had to pay for your service and I wasn't able to so didn't think this would go any further, but thank you.

    Linda

  • sam gerban
    sam gerban May 11, 2010

    what is the displyed message ..need to know

    if its keeps rebooting (restarting). Display indicates PLEASE WAIT. Will not allow faxes or copying.

    SOLUTION: If a NIC is installed, remove the NIC and verify operation. If reboot does not occur, replace PWB-P (p/n 4980-1019-02).
    hope than helps

    good luck

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 145 Answers

CAUSE: Failure of PWB-P.

SOLUTION: If a NIC is installed, remove the NIC and verify operation. If reboot does not occur, replace PWB-P (p/n 4980-1019-02).

hope that help

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After a paper jam it prints blanks


loose the static ,disconnect from pc and restart both of them together so sync is possible

May 08, 2009 | HP PhotoSmart C4480 All-in-One Printer ...

1 Answer

"Error 1068 Could not start the Printer Spooler on local Computer"


I appreciate the opportunity to help you. Try the following:

Check dependency services on Print Spooler
================================
1.Click "Start", input "services.msc" (without quotation marks) to Start Search bar and press "Enter".
2.Double click the “Print Spooler” service.
3.Choose “Dependencies” Tab and remember the services name.
4.In the service list window, find the dependency services and try to start them.
5.Please try to start the “Print Spooler” service again.



See if this helps. If it does, please fill in the rating of my service to you. Thanks for using Fixya.com


Jan 27, 2009 | Printers & Copiers

3 Answers

Konica Minolta Error Code: C14A3 Blown fuse or Exposure Lamp Printer was printing black and suspect it may be the lamp. Where can I get a replacement and instructions on replacing it myself?


Go to a Konica Minolta dealer and ask for assy, the part number is 4980 1001 01 and it is called CCD MODULE. I cannot find only the lamp, you'll have to replace the full assy in which the lamp is included.

Jan 15, 2009 | Konica Minolta Minolta DI1610FP...

1 Answer

5300 kodak printer installation


Hi again,

Appreciate the direct "Ask Me".

I was under the impression that she did respond to your post here as she has responded to my headsup.

Might I suggest that you:
Signin back to FixYa;
view/go to the Chat Session Transcript;
somewhere down the bottom would be "Post a Comment..." right below the "Print Session"
thereafter, the system would post both of your responses and seemingly continue the Chat though with some time delay.

Good luck and kind regards. Thank you for using FixYa again.


Oct 28, 2008 | Kodak EASYSHARE 5300 All-In-One InkJet...

2 Answers

Unable to reset printer after installing new ink cartridges


I want to known you have replaced the cartridges or refill the cartridges.

Feb 23, 2008 | Printers & Copiers

1 Answer

Unfixable?


all lights are flashing
the printer may need to be restarted
1. Press the Power button to turn off the printer, then press the Power button to
restart the printer.
Proceed to step 2 if the lights continue to flash.
2. Press the Power button to turn off the printer.
3. Disconnect the printer's power cord from the electrical outlet.
4. Reconnect the printer's power cord to the electrical outlet.
5. Press the Power button to turn on the printer.

If these steps do not work. It will need service, as a bad board may be the problem.

Here is the manual.

http://h10025.www1.hp.com/ewfrf/wc/manualCategory?product=304431&cc=us&lc=en&dlc=en&product=304431&dlc=en&lang=en

Nov 09, 2007 | HP DeskJet 5150 InkJet Printer

Not finding what you are looking for?
Konica Minolta DiALTA Di200 Copier Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Printers & Copiers Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

5695 Answers

David Burkhart
David Burkhart

Level 2 Expert

207 Answers

George Mclaughlin

Level 2 Expert

330 Answers

Are you a Konica Minolta Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...