Question about Kodak EASYSHARE 5300 All-In-One InkJet Printer

2 Answers

Printhead replacement Please detailed instruction to replace printhead on Kodak5300aio

Posted by on

  • Flora West
    Flora West Jan 01, 2009

    I have the 5300 printer and after replacing the cartridge for the very first time, it will not print legible. I thought I had purchased an old cartridge and went out and bought another new cartridge. Did all the alignment requirements and so forth. Now it prints very vaguely with lines or not at all. I have done all sorts of things I have been told to do on the internet. Nothing works. I'm beginning to think it is a piece of junk. It's been used hardly any.









  • plumbcharli Mar 11, 2009

    dont know how to remove printerhead

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

You may need to replace the printhead this is very easy to do first take out the ink cartrages and and look for the bulls eye right above the bulls eye there is a tab push tab to release printhead tray take out and replace with new one put tray in place and snap back into place replace ink cartrages.

Posted on Jan 01, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I need the telephone number to call to get a new printhead. This will be my 2nd one. When I replaced the first one the new printhead tore up a lot of envelopes. Took it out and replaced and it still did the same thing,

Posted on Jan 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lexmark intuition s505 has a printhead error


It sounds like a problem with the printhead. If your printer is still under warranty, please contact our technical support team to have the printhead replaced. You can find the contact details at support.lexmark.com.

If it's already out of warranty, you can purchase a printhead here: http://bit.ly/IZYhWo

Dec 02, 2012 | Lexmark Intuition S505 - multifunction ...

1 Answer

Printhead problem


It sounds like a problem with the printhead. If your printer is still under warranty, please contact our technical support team to have the printhead replaced. You can find the contact details at support.lexmark.com.


If it's already out of warranty, you can purchase a printhead here: http://bit.ly/IZYhWo

Dec 02, 2012 | Lexmark Intuition S505 - multifunction ...

1 Answer

Error message, printhead missing or not installed or has come loose. The printhead is in place, I removed the cartriges and removed the printhead then replaced them with the same results


help! I am looking for the solution! I also have a broken arm and i keep gettin timed out. Error message, printhead missing or not installed or has come loose.The printhead is in place, I removed the cartriges and removed the printhead then replaced them with the same results. I you can respond please instruct me whay to do. i have had my printer out for 10 days. ps, my phone number is 931 993 8269 email is jiyoung@fpunet.com

Dec 23, 2010 | Kodak ESP 5 Printer

1 Answer

Installation of printhead



Installation instructions for printhead for Kodak 5300 All-In-One printer

Do you CHARGE for information which should have been provided FREE with the printhead? Included with the printhead was an internet number for prodiving instructions, but they were not provided at this number.

Most fortunately, I located some old instructions which I already had!

Winnie Bauman

wobauman@gmail.com

Jan 20, 2009 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

How to remove a printhead from Kodak 5300


You can email tech support for instructions or call the toll free number below. These are the instructions for my KODAK 5100 from Kodak tech support.

Thank you for contacting Kodak technical support. If you should have any questions regarding the replacement of the printhead for your KODAK All-in-One Printer, support is available at 1.800.421.6699, 7:00 A.M. to midnight, 7 days a week.

Please check the following information how to install it:
a) Follow these instructions for step-by-step guidance on how to remove and replace your printhead.
b) If your printer is not powered on, press ON.
c) Lift the printer access door and wait for the carriage to move to the center position.
d) Remove any paper that may be loaded in the printer.
e) Remove both ink cartridges.
f) Unlatch the used printhead by pressing the button on the left.
g) Lift the used printhead out of the carriage.
h ) Remove the 3 plastic protective shields from the new printhead.
i) Place the printhead into the carriage
j) Push firmly against the back wall of the printehad until you hear a load snap.
k) Intall the new ink cartridges and make sure you hear the click into position.

If you need further assistance, please contact our Kodak technical support available at 1.800.421.6699, 7:00 A.M. to midnight, 7 days a week.

Jan 16, 2009 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

How to remove printhead


There is a release button up under the upper lip you need to push!

Jan 11, 2009 | Kodak EASYSHARE 5300 All-In-One InkJet...

12 Answers

Replacing printhead in Kodak 5300 All in One Printer


on this website:
http://www.kodak.com/global/plugins/acrobat/en/service/manuals/AiOPrinters/printhead/AUR1780-9_UE_RevC.pdf

You can find illustrated instructions on how to remove the old printhead, as well as on how to put the new printhead back in place.

You can easily go to that website by going to:
www.kodak.com/go/printheadsupport 

and selecting the second option "installing new printhead".

Nov 05, 2008 | Kodak EASYSHARE 5100 All-In-One Printer

2 Answers

Printhead needs replacing


The printhead is completely user replaceable and need no complicated instructions.

1. Remove the ink ribbon.
2. Looking from above, find a small shiny lever to the right of the printhead.
3. Lift the lever with your hand and remove the printhead by pulling it upwards (make sure the printer is cold).
4. Reverse the procedure to install the new printhead.

Be blessed.

Oct 31, 2008 | OKI MICROLINE 320 Turbo Matrix Printer

1 Answer

Print head failures HP 1050c


the tube system has an air leak causing a dryfire situation. air + printheads = damaged printheads. most users replace the black printhead more often than the colors. the seal where the printhead feed pin fits into the carriage is the end of the tube system. the hole in the seal becomes to large and doesn't properly seal the air out. order the tube system. complete and concise instructions are included in the box for tube replacement. this is considered an end user replaceable part. good luck! please rate this!

Sep 23, 2008 | HP DesignJet 1050c plus InkJet Printer

Not finding what you are looking for?
Kodak EASYSHARE 5300 All-In-One InkJet Printer Logo

Related Topics:

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kodak Printers & Copiers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Michel Smith

Level 3 Expert

1218 Answers

Sajid Najmi
Sajid Najmi

Level 1 Expert

31 Answers

Are you a Kodak Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...