Question about Electronics - Others

1 Answer

Installing acoustic research ar94 speakers

There are 6 sockets on the underside of these speakers, 3 red, 3 black. when I got them i unplugged 4 plugs that went to the amp. where do they all go? there are 2 red and 2 black sockets together, then a red and a black wire clip and then another red and black sockets

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Appart from the wire clips what type of connectors are there? are they RCA like on a TV?
If you are driving these speakers with an external amplifier then the red and black cable clips are your safest bet.
these connections are designed to carry an amplified signal. Unlike the RCA connections which are normally Line level.

Posted on Jan 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sansui rz 9500 av ... there is not sound output from this unit. when I test the test tone... there is sound ... all the speaker is in good condition ... it work for the pass few week but suddenly not


Please check the settings and speaker connections. Do keep it unplugged then reset.

Sep 28, 2012 | Electronics - Others

1 Answer

I have bose 401 speakers and need them to work with a stero that puts out 8ohms can you help?


Amps don't 'put out' 8-ohms; they're spec'd to drive a nominal load, usually 8-ohms, and always have some leeway as speakers are reactive loads that will vary with frequency.

You need to evaluate what your amp can do with a nominal 4-ohm load. The manual says they will work with amps rated for 4-8 ohm loads. Plug them in and keep an eye (and ear) out for any sign of stress (heat, distortion, smoke) when driving them hard.

Jul 16, 2011 | Hitachi Electronics - Others

1 Answer

My Faroudja DVP 2200 isn't working. It won’t turn on anymore. I removed the cover and checked the fuse – and it was fine. I am not sure is there is another fuse. I had some previous issues where it...


i would check ac plug change it if you could it probably had a short and maynot be visible also some fuses made be hidden on underside of board so check good you could overlook it easy

Aug 27, 2010 | Electronics - Others

1 Answer

Error region code ht-z220 pls want to know to set a free region


Ok, here is what you need to do :-
1. Remove any disc that might be in the machine
2. Unplug the power lead from the player
3. after 30 seconds reconnect the power lead
4. Turn on the dvd player with the remote and wait for "No Disc" to be displayed.
5. Press enter on the remote then press 8,4,2,6,9 then press enter. The dvd player should switch off
6. Turn the dvd player back on, then off again. Do this once more and it should now be region free

Hope this helps and thank you for using FixYa

Aug 23, 2010 | Samsung Electronics - Others

1 Answer

We bought the Sony CD/DVD (400 discs) in USA but live back in Oz.


To get to the menu with region type need to push stop twice and you get Check menu with:
0.Quit
1.All
2.Version
3.Peripherial
4.Servo
5.Supply
6.AV Decoder
7. Video
8.Audio

Push 2 and you get to the next menu
0.quit
1. All
2.Revision
3.Rum check Sum
4. Model type
5. Region
6. M't Check

Jan 04, 2010 | Sony Electronics - Others

1 Answer

Wireless speakers will not work.


Post the Model #'s of the products involved and I can be a little more specific. Using generic troubleshooting, First: make sure you have the wires for the receiving unit of the wireless speakers hooked up to either "A" Front or "B" Front. thenmake sure your receiver speaker switch for the corresponding location is on. It will light up on the front of the receiver either A, B, or both. Now, turn on the AV receiver and Tune it to a strong radio signal in your area, turn up the volume 1/4 to 1/2 way. Power the wireless units on. Both the speakers and their receiver should have a power button or at least a light to let you know they are getting signal. keep the speakers close and fine tune the wireless receiver with them until the led light on the front of the speakers is solid. You should have good audio at this point.

The other way the wireless receiver is hooked up is with RCA cables to the AV receiver. Without knowing what AV receiver you have, plug the RCA's into an "Output" like "Front Main Pre Out" or "VCR/Tape2 mon" or just plain "Monitor out" Depending on which Output you use will determine the setting on the receiver. If you need further clarification, post your equipment model numbers and I can tell you exactly what to do. Hope this helps

Jun 24, 2009 | Electronics - Others

1 Answer

Non Responsive Buttons


Hello..
Is this system one that has speaker connections?
If so, all the speakers must be connected for it to work right.

Apr 09, 2009 | Panasonic Electronics - Others

1 Answer

The power cord hard to unplug from back of tv for wall mounting job


step-1.
first switch off your tv unit and if possible switch off yuor main switch also
step-2.and pull out the plug bu holding the hand inth end of plug not in wire .
still you have the problem
follow step-1. and using wd 40 liqiud (available all electronic shops ) apply between wall socket and juntion of plug
and wait for five minites
then try step-2.
still you have the problem
finaly remove wall socket and try it now and remove the plug.

Oct 26, 2008 | Electronics - Others

1 Answer

Thanks but i need more help


Don't be panic.
Check the batteries of your remotes control. FIRST
Be sure to aim the control to the sensor of your tv.

Usually you have one remote for your tv and the other to control the cable box or digital box.

You have to set the RMC10 again using the code of your tv Silvania (like the first time)
Then set your tv on channel 3


Another thing, be sure that you are hitting the right buttons.
The control doesn't work if you hit on the top any key instead of cable
What i mean?

The remote has on the top 4 key usually (tv, cable, vcr, aux, etc).
You must hit first cable to set the control to cable

1, Manually turn on the device(TV, VCR, etc.) to be controlled.
2. Press and hold the code search button until the red indicator stays on, then release the code search button.
3. Press and quickly release the desired mode button (TV, VCR, ect.). The red indicator blinks off once.
4. Press the Channel up button repeatedly(up to 300 times) until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press channel down button to backtrack through the library until device changes channel. Pressing Channel up changes direction forward again.
5. Press and release Mute to install code.
1, Manually turn on the device(TV, VCR, etc.) to be controlled.
2. Press and hold the code search button until the red indicator stays on, then release the code search button.
3. Press and quickly release the desired mode button (TV, VCR, ect.). The red indicator blinks off once.
4. Press the Channel up button repeatedly(up to 300 times) until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press channel down button to backtrack through the library until device changes channel. Pressing Channel up changes direction forward again.
5. Press and release Mute to install code.


Don't forget to rate my help!
Thank you for using FIXYA!
Have a great day!
Pablo :-)

Let me know how it is going!

Oct 18, 2008 | Electronics - Others

3 Answers

Rca model r52wh74


You could get into service mode and set the convergence. The only problem is....RCA decided to remove it from the menu for the R52WH74. It only runs 1 time during the first setup, according to RCA Customer Service. This is the 2nd one I've bougt in 6 years. Enough RCA Garbage!

Dec 02, 2007 | RCA (T120PAK12) VHS Tape (12-Pack)

Not finding what you are looking for?
Electronics - Others Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electronics - Others Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

kakima

Level 3 Expert

98762 Answers

Are you an Electronics - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...