Question about Hotpoint WMA46 Front Load Washer

1 Answer

HOTPOINT WMA46 filter reconnect problem

My washing machine would not spin all the water, a bath mat had disintegrated, I got all the bots out of the filter the filter, I have replaced the filter but feel that I may not have replace it properly as it does not spin now. I am positive that maybe I have not put filter back in properly as it was awkward to put black cover back on

Dee

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hotpoint Master
  • 3,463 Answers

Regardless of the filter not being back in properly, this would not stop the m/c spinning. Remove the filter, and check it again for blockage. Push the hose on as far as it will go, or it will leak
Try spin again
Make sure you have not disturbed any wires to the motor, if still no spin, then remove motor and check carbons in motor.
Plz rate this solution.
Thanks.


Posted on Dec 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi we have a hotpoint aquarius extar 1300 spin wma46 that wont spin at all even with no clothes in ?


hello is it pumping out water if not check the pump for blockages it has to pump water out first then it should go into spin cycle. if does pump water out and still not spinning then there could be a problem with the module board this control the motor speeds hope it helps

regards
shaun

Mar 05, 2011 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

When I wash a bath mat the spin cycle never takes most of the water out of the mat so it is heavy with dripping water and difficult to put into the dryer. When I put on only the 'final spin' cyle it...


If your bath mat has a rubber backing, that would prevent the water from being centrifuged out of the mat. Even if you laid the mat in the drum with the wet side outwards, it would still only have a limited effect on removing the water.

Jan 26, 2011 | GE Washing Machines

1 Answer

Backimg to bath mat disintegrated in washer.


have you tried cleaning inside the rubber gromit attatched to the underneath of the drum? if its not that you might wanna try cleaning out the pump itself. may have jammed hope that helps

Feb 23, 2010 | LG WM-2277HW Front Load Washer

3 Answers

Washer won't spin. Washed bath mats (small) and


Read a post from someone else on this - turned out it works fine, just wouldn't work with the small wet load. I added towels to the bath mat load, washed them, it spins fine. Washed clothes & that worked fine too. Yay!! Not broken. Just not found of small loads of bath mats!

Jan 22, 2010 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Water will not drain from the machine. We washed a bathmat with a rubber backing and it came apart. Something is clogged, but the owner's manual just says to restart the DRAIN program. We've done that...


Hi,
Draining problem is very common in Bosch washers. However, it is very easy to fix.

1) Remove the white circular plate, located on the bottom left. Push a small screwdriver or needle through it and simultaneously rotate the plate clockwise.
2) Open the drain valve. Rotate the circular black handle counterclockwise. Beware of residual water.
3) Clean it. Re-assemble in reverse order.

Thanks for contacting fixya.com

Nov 24, 2009 | Bosch Nexxt 500 WFMC3301 Front Load Washer

2 Answers

WMA46 washing machine not draining, filter blocked but can't locate filter


the filter is underneath on the pipe going to the pump, you wiull need to remove a hose clip.

Jul 11, 2009 | Hotpoint WMA46 Front Load Washer

1 Answer

LG Washing Machine stops spinning in mid cycle


IE:

• Water supply is not adequate in
area.
• Water supply taps are not
completely open.
• Water inlet hose is bent.
• The filter of the inlet hose clogged.

Solution:
Check another tap in the house.
Fully open tap.
Straighten hose.
Check the filter of the inlet hose.

UE:
• Load is too small.
• Load is out of balance.
• The appliance has an imbalance
detection and correction system. If
individual heavy articles are loaded
(bath mat, bath robe, etc.) and the
imbalance is too great, after several
attempts to restart the spin cycle the
machine will stop and the error code
will be displayed.

Solution:
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning.
UE:

Apr 27, 2009 | LG WM2487H Front Load Washer

2 Answers

I have a bath mat that I washed in my duet washer successfully twice. Now when the cycle is complete the bath mat is drenched and apparatly no water was extracted from it. I'm frustrated. Another frequent...


Out of balance with wet, heavy rug.

Bathmat is border-line on being excessively heavy (wet)
Do not use in washer. The fact that you got away with it before is your hint NOT to do this again or else bigger problems???

Apr 20, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Pre wash not happening


poss blocked filter which also controls your pressure system, on your machine I believe if the prewash ligbt is flashing it would indicate a blockage there

Jun 13, 2007 | Hotpoint WMA46 Front Load Washer

1 Answer

Washing still wet - door won't open.


not a fault with washer. i guess you are plumbed into trap under sink. the spigot you fastened drain hose to is blanked off - there are various methods of doing this including have to saw off the end of the spigot with the bread knife. possible also a fault with pump or filter

Nov 16, 2006 | Hotpoint WMA46 Front Load Washer

Not finding what you are looking for?
Hotpoint WMA46 Front Load Washer Logo

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...