Question about Air Tools & Compressors

1 Answer

Ducati 900 SS 1992

Hi there i have a problem with my bike, every thing was going smooth, never given me any problem its been two years i had this bike, i service it my self eg: brake pads, oil.

When i try to run in speed it will give me a jurk and then move while moving, or in other words when the bike is in running condition and if i want to speed it will not perform and burn more gas, i have recently changed the Air filter my understanding is there either the fuel pump.

what do you have to say........

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 70 Answers

Try this question under motorcycle it was put under air compressor forum it will go to different experts Good luck let me know if this helps.

Posted on Jan 09, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a Clarke compressor, 4 hp single phase, it is just over a year old and on Friday it started getting to its full capacity then getting noisy and tripping out

did you drained water and sludge from the tank and oiler?

did you check oil level and changed it?

do your pressure sensor react to the pressure?

these are the items to check - as you did not bother to inform us what model - only general advice can be given... for future references - give us a better chance and provide manufacturer, model, year and in computers operating system as well...

Apr 05, 2015 | Clarke Air Tools & Compressors

1 Answer

I have an old air compressor that I have replaced the motor magstart and pressure switch on the motor is a 220 / 240 volt 5 horsepower motor it also has a low pressure oil cutoff switch does anybody have a...

Control: L1-SS-P-O-OL-OL-M-L2 In series, L1 is line 1, SS is start/stop switch, P is pressure switch, O is oil switch, OL is overload contact, M is magnetic coil (solenoid), L2 is line 2.
The voltage of M must be rated for the control voltage, across the line voltage (240V) or of a control transformer voltage, e.g. 240v/24v. A control voltage would be wired across the line, to L1 and L2.
Power: L1-T1-OL-M1, L2-T2-OL-M2. Line one to Line 1 on contactor, T1 on contactor jumpered to OL (overload heater) and out the overload heater terminal M1 to the motor terminal 1. Same for line 2, Line 2 to L2 on contactor, T2 on contactor jumpered to OL (overload heater) and out the heater overload terminal to M2 motor terminal.
The heater overload relays needs to be chosen by the motor full load current, a chart is given with a motor starter on selecting heater size. If no chart is available, go 115% of the motor FLA (full load amps) to select a heater size. E.G. 25 FLA motor at 115% is 28.75a. Sorry, no schematic available now, draw your own from this info. If using 3 phase, add the third line as duplicating one other line1 or line 2

Mar 10, 2015 | Air Tools & Compressors

1 Answer

Air leaking near power switch on my husky pro 2 hp 30 gal air compressor Made by Campbell Hausfeld. Have had it for 2-3 years and haven't run. It in over a year. What do I need to replace? Is there any...

Check all your connections with soapy water... find the bubbles. If it is coming from the end of a small tube with a needle sticking out of it then it is probably your check valve. Find it and pull it. Look for pieces of dirt and worse impressions left by pieces of dirt. Dirt wipes off, put if back in... impressions, need to get completely smooth with emery cloth and put it back in.

Apr 21, 2013 | Air Tools & Compressors

1 Answer

Need torque sequence for head on model ss-3 compressor

Always start inside and work outwards while going 180 degrees acrosss each new bolt, dont get them to rated torque all at one time work in a sereis of increments always inside to out and across from each other and you will be fine, car wheels , everything is this way.

Mar 03, 2012 | Ingersoll Air Tools & Compressors

1 Answer

Im plugged directly into a good outlet no exstension cord but reset keeps tripping on compressor every 30 seconds. outlet is not the problem. what else could it be?

If you are plugged into a 10 amp circuit or if the line from the circuit breaker to the outlet is long or 14 guage wire, it could possibly still be the outlet. Try plugging the compressor in to an outlet closer to the circuit box to see if the problem persists.

On the compressor the only thing that would create problems like you're describing is excessive friction in the moving parts. Check where two parts that move together are not doing so without excessive wear or heat. Check to see if the motor is turning freely, the eccentric to connecting rod joint should be free moving and smooth and the piston in the cylinder should be tight but smoothly operating.

Feb 01, 2011 | Makita MAC5200 Electric Powered Air...

1 Answer

More RPM Issues for Tools 1) Have old jointer with motor..1725rpm 5 1/2" pulley.. pulley on jointer is 2 1/2" ..what is 4" jointer blade speed ? also looking for right speed for 4" jointer.. 2)...

I had the same problem a while back, But I didn't bother with exact speed, what I cared more about was power and speed, and not bogging down. And I had it running smooth. Of course I have no idea what the pulley diameters were, but it sounds like you should be real close with the 2 1/2 inch at the head and 5 1/2 inch at the motor spinning 1725, should be about 900? So to get 700, bring the 5 1/2 down to 4 1/2, see if it has enough speed/power.

Feb 13, 2010 | Air Tools & Compressors

1 Answer

Ive got a compair c42 compressor and oil is coming out with the air.i have alredy replaced the seperator filter and all pipes and valves have been cleaned and are fine but the oil is still coming out.the...

sounds like the scavenge line is plugged or not installed correctly, this is something you may want to contact me on, as it could be a number of problems besides this also that could affect this problem. please check out my web site,

Dec 08, 2009 | Air Tools & Compressors

1 Answer

How to use the tire pump tool on the quickpump.

I have the instructions if you send me your e-mail address i will send them to you.

Jul 10, 2009 | Air Tools & Compressors

Not finding what you are looking for?
Air Tools & Compressors Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1383 Answers

Brad Brown

Level 3 Expert

14374 Answers

james allen
james allen

Level 2 Expert

109 Answers

Are you an Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides