Question about WYSE Winterm S30 Network Terminal

1 Answer

S30 Display Problems

Hi I have a couble of S30´s and they all have the same problem: Graphic i very slow. (i have som S10´s also, they are very fast) When you scroll down af Word og IE page, its very slow. Anyone seen this problem and fixet it ? Regards Martin

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.


    An expert who has answered 20 questions.

  • Expert
  • 112 Answers
Re: S30 Display Problems

In almost all cases of my dealing with Thin Clients over a 10/100bps network all problems usually are within the Terminal Servers hosting the Thin Clients. BPCS

Posted on Dec 12, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Does the wyse sxo have a speaker

No, I do not believe the "S" series (S10, S30, S50 & S90) have any speakers.

Mar 01, 2013 | WYSE Winterm S30 Network Terminal

1 Answer

Wyse 1200LE - error - out of frequency

This is caused by the terminals default display resolution (or the resolution that it was set to in its previous environment). The easiest way to get a display, would be to use a different monitor with a higher range of supported resolutions.

Fingers crossed the previous wnos.ini file would allow a G-key reset. If so, just hold down the G key when the terminal is booting, and it will reset to factory defaults. This might allow your monitor to work. (I think the default resolution is 800x600)

The problem you have is that the terminal might be locked down via the .ini file. So changing the configuration might be difficult. You could use a program like Wireshark to perform a network trace, this would tell you where the terminal is looking for it its wnos.ini file.

Then you will be able to setup a new wnos.ini on an FTP server set to the IP address(and path) the terminal is looking for, and this will allow you to set your own configuration.

May 28, 2009 | WYSE Winterm S30 Network Terminal

1 Answer

Wyse S10 RPD to Server 2008

you have to buy 1 terminal license for you S10 also.

Apr 23, 2009 | WYSE S10 (90210501) Network Terminal

3 Answers


Try resetting with Control + g rather than just g

Turn on the Winterm and immediately hold control + g (at the same time)

The display should flicker for a bit then release the control + g

This will reset the device to factory defaults, (you'll lose your connection settings, network settings, etc) -- but you'll be able to use it again. :)

Feb 11, 2009 | WYSE Winterm S30 Network Terminal

1 Answer

Howto add a network printer on Wyse winterm S30 terminal?

The S30 terminal has the CE 5.0 operating system loaded as default. So you are limited by the operating system and not the hardware when it comes to network printing.

Here is a extract of the release notes for Windows CE 5.0:

"In Windows CE, TCP/IP supports network printing through the Server Message Block (SMB) protocol. It does not provide the Windows Line Printer Remote (LPR) Spooler. However, independent software vendors (ISVs) and original equipment manufacturers (OEMs) can add this support."

In short, you need a 3rd party software program or a (SMB) printer server setup to setup network printing on the S30 terminal..

Wyse also have add-on software to help, if you have CE 5.0 loaded then try the "Thinprint" add-on supplied as a free download by them.
Download Link:

I haven't tried this, so let me know if it works.

May 02, 2008 | WYSE Winterm S30 Network Terminal

1 Answer

Wyse 1200LE - error - out of frequency

The display settings are not valid with the monitor. Either you are using a new monitor or you have changed the settings. If you are using a new monitor, swap with the old monitor and configure the appropriate refresh rate for the new monitor.

If you have changed the settings you may need to either reset all default settings, or setup a parallel unit and use the same key strokes to change the display settings on the problem unit.


Apr 02, 2008 | WYSE Winterm S30 Network Terminal

4 Answers

WYSE S10 Power up problem

Replacing C38 will fix the problem. It's a Lytics SMD Capacitor 47uF/10.3V.

Oct 26, 2007 | WYSE Winterm S30 Network Terminal

1 Answer

Display problems

There is a hotfix you can download from the WYSE Website but you have to setup a FTP server to get it installed. An easier way that seemed to work for us so far is go into Control Panel -> System -> Memory Tab. Adjust the memory slider so about 1/4 of the memory is set aside for Storage Memory (The systems I changed had between 90-100% set aside for Program Memory leaving 0-10% for Storage Memory.

Feb 23, 2007 | WYSE Winterm S30 Network Terminal

Not finding what you are looking for?
WYSE Winterm S30 Network Terminal Logo

Related Topics:

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top WYSE Network Terminals Experts

Rick Johnson
Rick Johnson

Level 2 Expert

84 Answers

Brad Brown

Level 3 Expert

13362 Answers

Mike Neath
Mike Neath

Level 3 Expert

315 Answers

Are you a WYSE Network Terminal Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides