Question about Kenmore 62622 Microwave Oven

2 Answers

Trying to remove built in Kenmore microwave 1994 #89755

I am trying to remove my microwave without totally wrecking it or my kitchen. I put it in my house when I built it in 1994 and it has finally blown. I can't seem to get it out. Any ideas? I unscrewed the 2 screws atop but apparently there is something more holding it.

Posted by on

  • Anonymous Jan 22, 2009

    removed the 2 screws but still cant remove it

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There are 2 more mounting bolts behind the plastic grill on the front of the microwave. They're about an inch down from the top and go all the way through and screw in to the wall bracket.

Posted on Aug 29, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 8,820 Answers

You may be able to download the installation instructions from the Sears parts site.

Just enter your model number there.

A full Sears/Kenmore model number has 3 digits, a dot, then 8 more digits, such as ###.########

On the resulting page, look to the right for the blue "View manuals" button. Click it.

trying to remove built in Kenmore microwave 1994 # - eeee82c.jpg

That Sears-related site has many free manuals. While the manuals they list there are all free, they will ask you to register.

Many times, the owner's manual will have the installation instructions inside.

If yours is not listed there for free, you would have to order it through the
Sears parts site.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Posted on Jan 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The kitchen timer button does not work on my Kenmore circular wave microwave.


If it has membrane switches, you might have a bad switch. Or, you could have a bad connection between the touch panel and the circuit board. Or the circuit board itself could have a problem.

Jul 25, 2016 | Kenmore Microwave Ovens

Tip

Error Code "d" - Microwave does not heat


The microwave could be in "Demo Mode" - Check your owners manual.

In Whirlpool/Kenmore models this is indicated by a lower case "d" on the right side of the display panel.

Most/All function except the magnatron (heat) work in demo mode so you can can learn to use the oven without actually cooking food

To clear "demo mode" press the "kitchen timer" pad and hold for 5 seconds until the "d" clears from the display... you may hear 2 beeps.

on Jun 16, 2009 | Kenmore 60654 Microwave Oven

1 Answer

Overheating bottom Kenmore 66560652000


Hi,

I would suspect that when the microwave oven was on the table the vent or air openings were restricted by the table. Without free flowing air the control and other components could build up heat. It is doubtful that you built up enough heat to damage anything as this unit has more than one over temperature safety devices built into it.

That being said, the excess heat could weaken something internally especially on the control that would cause it to fail sooner than later in life.

My advice would be to leave it unplugged until it is mounted back on the wall per the instructions and use it then as normal. If it fails in the next year or so replace it at that time.

May 03, 2010 | Kenmore Microwave Ovens

2 Answers

I have the Kenmoore Microwave Hood 721.80402. During this last wave of storms, I was without power for 2 days. Once the power was restored, the microwave will not work. Everything is plugged in and the...


You might try pulling the plug on the unit and leaving it overnight. The electronics may have locked up due to irregular voltage during the failure. There may also be a GFI (ground fault interrupter) on that circuit that has tripped for the same reason. Check the kitchen outlets for a tripped GFI.

Feb 14, 2010 | Kenmore 62622 Microwave Oven

1 Answer

Kenmore built in microwave displaying "D" and wont heat.


"d" may mean demo mode. The first thing to try is a "hard reset". Unplug it from the power outlet for 10 minutes, plug it back in, set the clock, then try again.

Jun 06, 2009 | Kenmore 62622 Microwave Oven

1 Answer

Trying to remove built in Kenmore microwave 1994 #89755?


A family member removed it while I was away. Returned home a short time later & it was outside under the C/P. Thanks anyway.
A.J.M.

Dec 30, 2008 | Kenmore 62622 Microwave Oven

1 Answer

Kenmore 565.6050.9990 microwave dead


Start taking all screws out until you can access fuse.

Sep 17, 2008 | Kenmore 62622 Microwave Oven

Not finding what you are looking for?
Kenmore 62622 Microwave Oven Logo

481 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Microwave Ovens Experts

William Miller
William Miller

Level 3 Expert

8820 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a Kenmore Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...