Question about Whirlpool LGQ9858PG Gas Dryer

1 Answer

I have a Whirlpool GGQ8858HZ0 and it suddenly stopped getting hot everthing else is working

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 214 Answers

So if no heat you have to remove backpanel off then cheak your thermal cut off locted on top of element housing and element with voltage meter .see if there is current trew both if not then it needs replacing you can buy a meter for under 20 bucks well worth if you like to fix things on your own good luck:)

Posted on May 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am having whirlpool washing machine model-whitemagic FSAN652 during washing machine suddenly stopped working and an error PE is displayed pl give me suggestion to rectify


whirlpool have a good fault code list on the net
go google and type in whirlpool top loader model------ and look for pdf version of manual or fault codes.

Jun 28, 2015 | Whirlpool Washing Machines

1 Answer

Washer temp setting changes by itself


I also have a Whirlpool washer/dryer for my condo, although I don't know the model number of mine. I had the same problem -- after it was precisely a year old, suddenly one day the hot and cold started coming out reversed. I was able to fix mine by more or less temporarily fiddling with the water pressure. What I did was one time, when the rinse cycle was running and the washer was filling up with hot water (grrrr...), I completely shut off the valve supplying hot water. So at that point the water stopped filling into the washer, and then I started tinkering with the cold water, twisting the valve off and on a few times. Then BINGO, suddenly the cold water "kicked in" and for the remainder of the rinse cycle, it filled the washer with cold water. I then turned the hot water valve back on, and since then it has been running correctly.

Jun 05, 2010 | Whirlpool Washing Machines

1 Answer

Whirlpool top load washer makes noise on filling


Its mainly caused by back pressure when the inlet valve suddenly shuts off the water to the machine. The pressure causes your plumbing pipe work to shake inside the walls.

You can turn down the pressure by closing your water tap and only having it slightly open. Or you can get pressure limiters which join on the hose.

Regards
Ash

Oct 26, 2009 | Whirlpool Washing Machines

1 Answer

How do i clean the Whirlpool Gold american collection top loading washing machine? I can see no filter to remove and the inside of the tub is getting dirty. The holes inside the tub at the top seem to be...


Dumped even more HOT HOT HOT water while poking around inside dispenser. Softener dispenser suddenly became unclogged and water began running out of the opening showing me that the dispenser was indeed clogged with softener buildup.

Sep 20, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Whirlpool AWM 045-1000 washing machine has suddenly stopped working and warning light "WATER STOP" has come on. Any ideas for a fix?


Whirlpool AWM 045-1000 washing machine has suddenly stopped working and warning light "WATER STOP" has come on. Any ideas for a fix?

Sep 19, 2009 | Whirlpool Washing Machines

1 Answer

Washing machine won't complete cycle


If it is a hot and cold fill washer, yes, then it could be a hot water problem related to the valve, or the water supply., if it is cold fill only, then the problem is elsewhere.
Pleas rate my solutikon.
Thanks.

May 13, 2009 | Whirlpool AWM5125/1 Front Load Washer

1 Answer

I have a Whirlpool AWG338 that has suddenly stopped drawing water. It will run a cycle as if water is there but never actually draws from the main. It has both hot and cold supply.


If water is not getting into the machine, and the hot and cold water faucets are connected, and have good pressure, then parts that can cause the problem are inlet valve, water level switch and timer control.

To start cut power to the applianc3e for five minutes, this can fix a jammed timer control.

If that does not work you may need to call a repairman to test the following:

The inlet valve must be tested by energizing it , testing valve solenoid, and reading voltages to identify a fault in wiring (contact).

If the inlet valve is fine when tested, worth having a look at the water level switch, if it is stuck on overfill position , it will prevent water from getting into the machine.

Lastly,the timer control board should be tested, to ensure that the problem is not a faulty timer keeping the inlet valve on close position.



Mar 30, 2009 | Whirlpool Washing Machines

1 Answer

Whirlpool Top Loading Washer not filling when set on hot only


check the water inlet valve assembly. Also, this could be a timer issue as well. check the Hot valve block connector on the control panel board. it could be lose or separated or broken. there is a wire that leads to the valve on the hot side as well. check this.

Mar 13, 2009 | Washing Machines

Not finding what you are looking for?
Whirlpool LGQ9858PG Gas Dryer Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...