Question about Linksys Wireless-G WRTP54G Router

1 Answer

Factory default password/user name

When i tried to reset the router (F/D) it ask for the user name/password from service provider. who is it? i hav virgin B.B and a sip device attached. i hve done hard reset, but what i wanted to do is to update the firmware, without the login details it would not let me update the firmware. thanks

Posted by on

  • anooppd Jan 03, 2009

    thanks buddy, i dont hav to login to access internet and linksys no longer support this device as these are made for vonage. Hands off, i sent it back yesterday for a refund and the general feed back of this device is its a piece of ****!!!!. uless u unlock it and flash it with new firmware. Today i ordered Tpt 300 another one from linksys hopes it would do the work !! But shame on linksys and vonage. Why dont they provide lastest firmware? why would they lock the device? Its customers decision to choose the provider!!!

  • jc21echo May 11, 2010

    Do you need the login/password for the router, or for your internet service provider?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 192 Answers

Contact linksas they might know

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

FORGOT MY PASSWORD TO GETON wifi


Wireless or Wi-Fi Internet is convenient because it allows many people who have laptops to connect to the Web anywhere within their homes or businesses.
The downside to wireless is that anyone with a laptop or a smartphone within a short distance of a router can access it.
That is why it is often password-protected.
Some Internet service providers let you choose a password that you can remember, while others will give you a very long, case-sensitive code.
If you lose or forget your password, you can usually get it from your modem or your Internet service provider.

Look on your modem.
This is the box that your Internet service provider gave you when your Internet service was installed.
Some Internet Service providers put your wireless password directly on the box along with your user-name.
A modem may or may not be separate from a router, which sends out the wireless signals.
If you have two boxes and are unsure which is which, look at both.
Call your Internet service provider if you cannot find a password on the modem.
You can also try online customer service through your service provider's website if you are able to get Internet access apart from your wireless connection.
Talk to a customer service representive and ask to retrieve your password.
You may be required to change it.
Be prepared to provide security information that the service provider has on file, such as your Social Security number, phone number, address or another personal security question.

also reset your password
If a password is forgotten or lost, the password can be recovered or reset by accessing the router's Web-based settings menu.
Most wireless routers also have a reset button, which is capable of returning the router to its default settings which includes resetting the password.

Connect to your Wi-Fi or attach your computer directly to the router with an Ethernet cable.
Open your Web browser.
Enter the default address of your router.
The default address is listed in your user manual or on the product website.
Linksys and 3Com routers typically use "192.168.1.1" while Netgear routers use "192.168.0.1."

Enter your username and password. Many routers use "admin" for the username and password by default.

Locate the wireless security settings. Disable the wireless security.
Reset to Factory Defaults
Locate the reset button on your router.
Typically the reset button is a small indented hole on the back of the device.

Insert a long thin object such as a paperclip and hold down the reset button for 30 seconds to revert the router to its factory default settings.
Open your Web browser.
Enter the default address of your router.
The default address is listed in your user manual or on the product website.
Linksys and 3Com routers typically use "192.168.1.1" while Netgear routers use "192.168.0.1."

Enter your username and password.
Many routers use "admin" for the username and password by default.

Locate the wireless security settings and add security as necessary.

How To Reset Your Router's Password
http://www.lostintechnology.com/how-to/how-to-reset-your-routers-password

Jul 11, 2013 | Routers

1 Answer

I cant setup my router to my computer


Press RESET button it is in the back side of router then all settings goes to factory defaults. Then connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
For belkin router http://192.168.15.1
or
http://192.168.2.1

If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Click on wireless settings enable wifi Click on WAN settings set it as internet service provider enable DHCP Then save settings and restart router.
Thanks for using FixYa.

Oct 09, 2011 | Cisco Linksys E1000 WirelessN Broadband...

2 Answers

Forget user name and password how to set up new ones


You may have to resent the router for that purpose! User name and password are usually default for each router. If you have not set up a user name or password try default admin in password section and leave user name blank. If you have set up a user name and password and forgot now then you may have to reset the router by pressing reset button on back of router for 30 to 60 seconds which brings back factory default settings for the router!

Sep 12, 2011 | Routers

1 Answer

Lost password


By default there is no user name and paswor. So try leaving the user name and password blank. If it doesn't work, reset the router. There should be a reset pinhole or button to bring the router to it's factory settings. After resetting the router, try the default user name and password again.

May 21, 2011 | Proxim SkyLine Wireless Broadband Gateway...

2 Answers

I have forgoten my password. plz help me to get it reset


You need to configure your router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then set WAN settings as internet service provider settings enable DHCP. . Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Jan 22, 2011 | Routers

1 Answer

How can i get password to access router from my loptop via WIFI or how can i know the password that came from the factory


Most of the time the user manual provides the default user name and password for the router model. Most seem to come default with admin/admin. If this has been changed and forgotten press in the reset button for 10 - 20 seconds will reset the router to factory defaults. Usually

Oct 07, 2010 | EnGenius ESR9753 Wireless N Router Point ...

1 Answer

Same problem


Reset your router to factory default settings for that press RESET button for 10 seconds it is in back side of router then all settings defaults.Then configure your router with below method then all messup will be fixed. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then click on WAn settings and set wan settings as internet service provider settings. Then click on wireless settings then enable wifi also enter SSID name and enable broad cast turn on wifi . If you want to secure wifi then enable WEP in wireless security .Enter code it is your password to connect wifi. Let me know if you need further assistance. Thanks for using FixYa.

Aug 03, 2010 | Routers

1 Answer

All lights for my Belkin N router are on except for the 'wireless light'. Also 'Security' light keeps on flashing. How do i fix this so that all lights are on?


Possible the wireless capabilitiy of your router is turned off and the security is turned off meaning that there is no security key in the router settings yet,

you will need to get in your routers default gateway check by going into the Dos Promp, type in IPCONFIG this will show you your IP address and default gateway type your default gateway in the address bar of your browser IE or Firefox ths should ask for a user name and password to get in your router the default user name will be admin and the password can be blank or password, or admin as well, depnds if your internet service provider change the password and user name of the router. once in the router check wireless settings look if the wireless is turned on the router and for the security just create a network security key to hav that light turned on if you want.

Jun 14, 2010 | Belkin N Wireless Modem-Router F5D8633au4A

1 Answer

Change the local IP address of Billion 400G


You need to login to the router page with the IP 10.0.0.2 and the on that and you can change the IP from that page
On login it will ask for username and password it is admin and password is "password" by default if you have any issue in getting user name and password you can reset the router as below

To restore the factory default configuration settings without knowing the administration password or IP address, you must use the Default Reset button on the rear panel of the router. 1. Press and hold the Default Reset button until the Test LED turns on (about 10 seconds). 2. Release the Default Reset button and wait for the router to reboot.
it will come back to factory settings of 192.168.1.1 and then you need to configure the router as per your internet service provider

you can check the manual at the below link
http://kbserver.netgear.com/pdf/dg834g_dg834gb_ref_manual_03Jun05.pdf



Nov 27, 2009 | NetGear DG834G 802.11G Wireless ADSL...

2 Answers

Setup of municipal wifi


It sounds like you'll need to reset the router to factory defaults, here's how to do this:
With the router powered on, press and hold the reset button for exactly seven seconds, this will restore the router to factory default.


Note: By default the password on the router is left blank, and the
default IP address is 192.168.2.1



Hope this helps!

Feb 07, 2008 | Belkin (F5D7230-4) Router (587009)

Not finding what you are looking for?
Linksys Wireless-G WRTP54G Router Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Mike

Level 3 Expert

4331 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Linksys Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...