Question about Ingersoll Rand 231C-KS - 1/2" Super Duty Air Impact Wrench Kit With Flip Socket Set And Bit Dr - - Ingersoll-Rand - IR 231C-KS

Open Question

Muje M925 ka Audio Driver Chahiye

Board Number M925 I Requir audio Driver Of This Board

Posted by on

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Nails fail to feed

Without knowing your model number here are some things to check, in order of difficulty:
1. First make sure you're using the proper nails for your gun. If your gun isn't specifically listed on the box of nails as compatable make sure they are seating in your gun properly. Some brands of angled nails are a couple degrees off from others and won't work in competetor's guns.
2. Check the entire feed path of the nails in the magazine all the way up to where the driver catches the next nail. Sometimes dirt builds up in the track or there could be a peice of nail stuck in there preventing the nails from getting under the driver. Also the spring on the feed shoe should have strong pressure on the shoe all the way up to the head and the shoe has to ride freely in the magazine.
3. If the gun is making holes in the wood the driver isn't broke but it must be straight and true and the tip square. If not it will miss or slip off the nail before driving it. The only way to check the driver is to remove the head on the gun and take the driver out. The piston & driver should travel from the top to the bottom of the cylinder without binding anywhere. Correct any problems you find or replace any damaged parts and your gun should work.

Feb 13, 2012 | Porter Cable 16 - Gauge Finish Brad Nailer...

1 Answer

My porter cable Finish Nailer 250B has a broken part. It is 119 by the parts list and Part number 904695. It looks like it does not come with gaskets/o rings. Is this something I can replace myself or...

You can reuse the oring from the old cylinder. Easy to install. The cylinder will break when the driver bends or breaks. If the driver looks good, dont worry about anything. Remove nails. Slip the driver into the cylinder and push driver and cylinder into body of the gun. Replace head.

Apr 29, 2011 | Porter Cable 16 - Gauge Finish Brad Nailer...

2 Answers

Mic not working

click start control panel sounds and audio devices select advanced there might be a tick in the mute box untick it or select audio from the microphone drop down list make sure you have the right one selected and in the volume box make sure the microphone box has a tick in it or select the voice tab and make sure that you have the right media selected also select volume make sure the box for microphone has a tick in it
hope this helps

Feb 07, 2011 | Milwaukee Tool Case Heat Gun

1 Answer

Nail driver slide wont retract

You have worn o-rings. You can go to and find a breakdown of your nailer. On the left side of the page go to 'Schematics and Parts', find your model number and a parts list will come up. Unfortunately Bostitch doesn't make many repair kits for their guns, you have to order all of the o-rings individually. Replace all of them, if one or two are worn the rest are not far behind. You can order them from Stanley Bostitch or get the part numbers and find another vendor.

Sep 02, 2010 | Stanley Bostitch N88rh Framing Nailer...

1 Answer

Hi, i lost the sound on my HP desk top. pls help. John

lol funny. sorry go to the control panel/sounds and audio devices/audio and check that u have a default driver if not go to and download your sound driver for your type comp.hope this helps

Jun 29, 2010 | Air Tools & Compressors

1 Answer

My 1/2 inch drive air drill stopped working i have model number 19912.motor is running but chack is not turning

MOst likely the planetary gears in the head og the drill. There is a small pinion gear which drives the larger gear to make the chuck turn.

Jan 10, 2010 | Craftsman Nailer Kit, Palm Air Driver

1 Answer

How to adjust the nailer, flooring is 5/8",so the cleats sit where it should be? How to avoid splitting the tongue on the wood?

You must put an in-line regulator at the inlet for the gun. Turn your preasure to 90 psi and use a sample board to get the fine tune adjustment at the gun. Turning down the air preasure will reduce the amount of force the anvil hits the nail with.

Nov 18, 2009 | Craftsman Nailer Kit, Palm Air Driver

2 Answers

Bostich N88rh fires like a machine gun

You either have a piston stop bumper failure or some damaged orings. Look on the schematic and the piston stop bumper is number 11, part #107236. A lot of times the piston stop bumper will disintergrate due to becoming brittle from the compressed air and not having enough lubrication. Look for small plastic balls in the head under the valve. If you see little plastic pieces than that is what remains of the piston stop bumper. You will need to remove the valve from the head cap in order to inspect the bumper. Also inspect all orings. The slightest damage can have big effects. One other thing to look for is damage to the plastic valve that rides on 3 orings. (2 out and 1 in) I don't believe you have valve damage because you say it is firing like a machine gun. This is almost always the piston stop bumper.

Sep 07, 2009 | Stanley Bostitch N88rh Framing Nailer...

Not finding what you are looking for?
Ingersoll Rand 231C-KS - 1/2" Super Duty Air Impact Wrench Kit With Flip Socket Set And Bit Dr - - Ingersoll-Rand - IR 231C-KS Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ingersoll Air Tools & Compressors Experts

John Trevino

Level 3 Expert

1378 Answers

Brad Brown

Level 3 Expert

13794 Answers


Level 3 Expert

63931 Answers

Are you an Ingersoll Air Tool and Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides