Question about Hobart A200 Stand Mixer

1 Answer

Hobart A200 We have a Hobart A200 and need a grinder attachement. Is this a #12 Hub? I have seen grinders for these on ebay for 92.00 is this a good one to use? http://cgi.ebay.com/Meat-Chopper-Attachment-1-12HCOMPL_W0QQitemZ110025401213QQcmdZViewItemQQptZLH_DefaultDomain_0?_trksid=p3286.m20.l1116 Thanks

Posted by on

  • perryburda Dec 29, 2008

    Thanks for the Info

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

Yes A-200 are number 12 I would find a hobart grinder they will have a big H in the casting on the neck get one with a stainless pan and stomper to push product down the throat. If you wait on Ebay and put it on your watch list they do come along. look for no rust. Make sure it has the big H in the casting. the other after market ones seem to not last long like the metal wears on the worm and hub to fast. also you always know where to get a piece if you need it if its a Hobart. not so with the forign jobs.

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Hobart grinder is old vintage it has 3 or 4 oil ports do I still use Mobil DTE HM OIL? How much in each port?


Steve I dont know that that is necessary. I have 2 a big heavy monster and a little #12 and I check for full and keep going. I only use mine in winter for sausage and its 50# in 120 sec. not much wear and tear on the lube. I know Hobart has a good web and mobile service here. Mine are Old and I'm guessing yours are too.
http://www.hobartcorp.com/

Jan 10, 2016 | Hobart Food Mixers

1 Answer

Need to adjust clutch on hobart 4346 meat grinder how do you do it?


On the 4346 mixer/grinder the clutch can't be adjusted. It is a Moorse clutch and will need to be replaced. If you ate handy buy the rebuild kit for the bottom end from Hobart. It's not cheap but once it's done it will last for years. Hope this helps, Food luck

Dec 16, 2012 | Hobart 4346 Meat Grinder Mixer Chopper...

1 Answer

Oil (or maybe broken down grease) leaking from the accessory hub of Hobart mixer.


You're right, it's broken down grease. The A200 doesn't have a rubber seal to prevent this from leaking, either. That's normally OK, when the grease in reasonable condition, but when it breaks down bad enough, you see what you're seeing. The grease needs to be changed which requires disassembly of the transmission. It's quite a job (and very messy) if you're not familiar with it, but if you're interested I know I've read (and may have written one) instructions on disassembling the transmission on this website. If you decide to do the job yourself, be sure to remove the attachment hub (comes out to the inside of the transmission) and clean the passage well.

Jun 09, 2010 | Hobart A200 Stand Mixer

1 Answer

What should i pay for a Hobart L-800?


See what they are selling for on ebay.

May 03, 2010 | Hobart Food Mixers

1 Answer

Hello, I have a commercial dough mixer,


it's a standard drive system found on most hobart mixers like the a200 style and you may find only hobart parts will fit it

Oct 10, 2009 | Hobart D300-6036 Mixer

1 Answer

I have oil coming from the front of a hobart a200 mixer,What to look for? and what kind of oil?


If you have oil leaking from the attachment hub, the transmission grease has liquified. The transmission will need to be opened so the old lubricant can be removed, by scooping it out. There aren't any seals in the attachment hub, just two torrington needle bearings. The helical gears thrust the pinion gear onto a thrust bearing in the hub to create a seal. The hub has a return hole in it's casting for excess lube to return internally. It's possible the return hole is restricted. On the other hand, if the machine has been filled with oil, it will probably leak like a siv.
The new lube should be 35 OZ of mobil XPH 222,
Hobart part number is 103881-47 for 32OZ.

Aug 04, 2009 | Hobart A200 Stand Mixer

1 Answer

Grinder attachment


Cindy,if it has a screw take it out,grab a flathead screwdriver and work your way around the cap.Some mixers have been painted or just the gunk over the years make the cap hard to pull off.The push button i have never seen on a hobart mixer near the hub.Give me the serial and spec number.

Nov 12, 2008 | Hobart A200 Stand Mixer

7 Answers

Manual for Hobart Mixer A200


You can go to hobartcorp.com and register for free then you can print or download a parts
manual to help you to do repair. Hobart provide service manual to their technician only.

May 05, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Hobart A200 Stand Mixer Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1138 Answers

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Shira

Level 2 Expert

119 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...