Question about Kenmore Oasis HE 27082 Top Load Washer

3 Answers

Washer displaying "LD" and constantly beeps

Washer starts like normal then either in the wash cycle or the spin cycle the machine starts beeping and displays LD on the screen
any idea what this might be?

Posted by on

  • 5 more comments 
  • Anonymous Dec 30, 2008

    I have the same problem and have already replaced the computer module several months ago. This thing has been nothing but problems!!!!!!!!

  • mikellyr
    mikellyr Jan 07, 2009

    I have the same problem as this. Can anyone help me!!?

  • okorchid7 Jan 08, 2009

    Sometimes when I first start cycle and sometimes at the rinse portion of the cycle.

  • Anonymous Jan 09, 2009

    The LD is long discharge of the water in the tank. I had the same problem and found a quarter blocking the drain hose. To remove, had to pull out the tank and remove the plastic cover over the drain. Now, it appears there is another problem for Sears Service replaced the computer, and has a replacement interface and replacement pump being shipped to my home. The bill so far for parts is $450. This machine is only 10 months old so it's all covered under warantee. In March '08, I had to replace a 4 1/2 year old Frigidaire front loader because it would cost more to replace the computer than to buy a new machine. Where the F%^& are these mechanical machines we had back in the 70's and 80's that would last 20 plus years with minimal failures? Guys, don't listen to the women that get turn on by all of the electronic features.

  • Anonymous Jan 16, 2009

    THE BAD WEATHER CAN AFFECT THE DRAIN SYSTEM OF KENMORE OASYS WASHER, BECAUSE ITS TO COLD?


  • shannon Jan 19, 2009

    we cleaned out hose and bottom of machine and was no help, then the sears repair guy put a new pump on , no help

    we spent 220 and now the sears repair guys says it gonna cost 200 more that we have to replace the control panel and he is not sure that will work

  • dearnhardtfn Apr 29, 2009

    I have the same problem ld code I cleaned out all the hoses there was not bloCkage and the drain is fine.It is barely 1 year and a half old .We have got nothing but run around from SEARS it has cost us a couple hun. for them to service it.Still no luck. Our previous washer also kenmore lasted almost 18 years go figure that the basic mechanical models work so much better.I will never shop at SEARS AGAIN..good job standing behind your product.

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 87 Answers

Sometimes the LD on certain machines can be decieving, It's possible that the error is pointing to a lid lock issue. I'm a sears tech but have logged of my work computer for the night so I can't look it up right now. I just happened to stumble on this forum. In all appliances there is a tech sheet hid somewhere. This will give you more information. On this model, if you press and hold anykey for 3-4 seconds, let it up for 3-4 second and do that 3 times it will show more codes and go into a test cycle. Don't worry you cant screw anything up in the controller. If you or anybody needs help on appliances you can drop me a line. I have been a Sears tech for 15 years and have seen a lot of stuff and learning more all the time. scottowa at hot mail

Posted on Jan 22, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Don't know if this sight would be helpful or not. I stumbled on it while searching for a solution with my kenmore elite oasis. I don't have the computer problems. My problem is i can hear sloshing when i manually agitate the washer. For some reason some water is being left behind at the end of each laundry job. Not even 2 yrs old yet. (even ran a spin cycle with no water or clothes and had the discharge hose laying on my basement floor, to have gravity take care of it) Still hear the sloshing. Good luck with your problems. Im stumped. www.toploadclassaction.com/kenmore.php

Posted on Jan 21, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 88 Answers

You probably have something in your pump . or a problem with your drain. Ld means the washer took longer then it should to drain.

Posted on Jan 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Model Gw709AU


When you start your machine is the water just go stop go stop,
Just wait for the machine to display an error code on the wash progress lights and beeps constantly.
It could be the Rotor Position Sensor, out of balance switch or lid magnetic reed switch.
Your error code will determine this.
Is your machine beeping & showing a weird pattern of lights on the wash cycle, It is displaying an error code,
To read this error code you start at the red spin light & work to the left only add up the lights that are on. Red spin light = 1 2nd rinse light =2 1st rinse light =4 last wash light=8 4th wash light=16 3rd wash light=32 2nd wash light=64 1st wash light=128
j8paojvh5jrgaaaaabjru5erkjggg==


2_26_2013_3_17_31_am.jpg

Feb 20, 2013 | Fisher and Paykel Washing Machines

1 Answer

I have a westinghouse lt955s. The machine is stopping while it is draining and on the display it keeps on flashing LD and the number of minutes left of the cycle. Does anyone know what LD means?


Ld = all water level lisghts flashing slowly accompanied by 5 fast beeps every 4 minutes - LID is open position

got this out of machine manual hope it helps

Oct 06, 2010 | Westinghouse WWS833ES Super Capacity Top...

1 Answer

When i put the wash cycle on it goes and does fill up with water, but then when comes to spin cycle it stops agitating and starts beeping constantly with the light on where the "lid locked" icon is.. When...


Hi Ellie,Just read your posting.Now does your machine drain most of the water from the machine but it does not spin the clothes dry?Is this correct?Also does the mahine only show the lid lock icon when the machine is beeping?Please reply with additional information on the questions and I am sure I can help you.Looking forward to your reply.

Aug 17, 2010 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

The machine will start a cycle normally, but after the timer reaches a certain point it stops counting down and the machine will continue to agitate until you force it to stop.


Thank you for verifying the model type so many folks post non FAV6800A/FAV9800A questions in this forum machine specific topic area.

FAV6800A/FAV9800A Service Manual for reference. Sears Parts Direct for reference.

You will need the Service Manual for support. I’m an owner like you with a solid repair skills on the machine and will try to help you DIY the repair if we can ID the issue through troubleshooting.

Do you have this condition in all wash cycles? Will a Quick Wash cycle complete? Do you see the Cycle Status LED ever indicate the machine has moved to the Spin Cycle during the wash cycle? This could be a Control Board failure but we need to troubleshoot.

I want to make sure the Wash basket will spin up with a Spin Only cycle selection. Can you select a Spin Only cycle with a empty wash basket. I would release the washer top so you can observe this test. I want to rule out a broken Clutch large wrap spring.

Page 33 of the Service Manual will show you how to release the washer top from the base. In Spin Only cycle raise the top just enough to make sure the wash basket is rotating Counter Clock Wise – CCW with the Spin Only cycle selected and operated.

If the above test doesn’t indicate an issue I would like you to try the Quick Service Cycle test on page 15 of the Service Manual and see if your FAV6800A will pass that test with no clothes in the washer. When you put the machine in Service Mode press and hold simultaneously the Enviro Plus and Spin Only keys until the machine beeps and the LED display reads 00. Then press Wash/Rinse Temp to start Quick Service Cycle test. Did the test complete with a PA indication in the display? It will only display the PA code for a few seconds. End of cycle will beep washer will unlock and Cycle Status LED will indicate complete.

Waiting for your reply….Rich

Dec 24, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag neptune washer keeps beeping


The Service Manual for reference. Sears Parts Direct for reference.
I have tried to work with a few folks on this issue never received feed back to resolution see this post. I feel the issue is caused by one of three possible issues.

A stuck key issue/defective Spin Cycle key making constant contact forcing the Key/LED to cycle thru the Spin Cycle settings. Under normal conditions if you press and hold the Spin Select key it will cycle thru the settings, yours has a mind of its own (defective issue).

A false signal from the Control Board for the Spin Cycle.

A corrosion path issue at the Membrane Pad ribbon cable socket connection between pins 5 and 4. See page 20 of the SM button functionality “Spin” key.

Try to verify that the spin cycle membrane key is not stuck/defective signaling the Control Board to cycle thru the spin settings. I have not experienced this issue but let’s try the Membrane Pad Test to get a start point. See the Service Manual page 15, I have modified the process to make it a bit more understandable at least for me. Make sure the two digit display is not On or Lite.
Press the off button first so there is nothing displayed in the Two Digit display of your FAV6800AW.

Now Enter / Exit Service Mode


To enter Service Mode press the Enviro Plus and Spin Only keys for three seconds or until the control beeps. While in Service Mode, pressing the Presoak key will start a membrane switch check that verifies switch operation.

All the LEDs (except Presoak ) can be toggled or slewed by pressing the key associated with the LED or set of LEDs. Do not press the Presoak again during this test.

Press each key once and only once including the Signal Key the on side and the off side, also the UP and Down Arrow key of the LED display. All keys (including the OFF button) must be pressed within 5 minutes for this test to pass. “PA” will be displayed for five (5) seconds once all keys have been pressed and the test is completed (more like PA will be displayed for only a few seconds on my FAV6800AW). Following 10 seconds of inactivity at any point, this test will exit without any display. Let us know the results.

See my additional comment this board has message limit issues.

Sep 17, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

END OF CYCLE KEEPS BEEPING WHILE WASHING


Maybe the machine is telling you that your load is uneven, When going through a spin cycle it will detect if the load is too heavy on one side. Just open the door and spread the load evenly. good luck.

Jan 26, 2009 | Whirlpool LHW0050PQ Front Load Washer

1 Answer

Kenmore HE3 washer emits steady, constant beeeeeeeeeeeeeep


Depending on how your washer controls the beeper, it could be a stuck relay or a fried transistor.

Jan 17, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

5 Answers

Whirlpool Cabrio WTW6600SW1: Won't drain


The washer drew half a tub of water on the "Bulky items" cycle, and stopped. All the lights on the cycle dial light up and flash, the machine beeps and the me error message in the "estimated time remaining" field is "Ld". I've tried to shut the machine down and change the cycle to "drain and spin" but it will not agitate, won't drain or spin.

Sep 05, 2008 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Washer beeps Ld a few minutes into each wash


LD means = Long Drain
Problaby samething inside the pump
Is your machine calypso

Apr 15, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Kenmore Oasis HE 27082 Top Load Washer Logo

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Fordexpert

Level 3 Expert

5331 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

reliableservice

Level 2 Expert

287 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...