Question about Printers & Copiers

1 Answer

Replace lamp on canon microfilm scanner 400

Machine is on, lamp is not. I would like to replace the lamp.

Posted by on

  • mrallen Jan 12, 2009

    We are having the same problem. Repeatedly calling in service repairs. Purchased new bulb holder but it light still goes off. Any suggestions?

  • sam gerban
    sam gerban May 11, 2010

    what model ?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Lamp unit is on right hand side of machine slides out like draw

Posted on Jul 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your question? e000225-0002 in canon ir 3300 machine please help


Hello, the error E225 it is used to indicate a fault in the scanning lamp (xenon tube).
This is the exact descreption of the error:
E225-0002
The edge gain correction level is different from the correction level for the preceding sheet by a specific level or more.

Please folow this steps:
If the machine has been recently cleaned at the scanner unit you can check if the xenon tube is well conected at both ends.
If the error is gone, and if the lamp turns on, after this check and after the starting of the machine you are good to go if not you will have to replace the lamp.
If the error will not go away after replacing the lamp you will have to replace the CCD unit and if still the error is not gone you will have to replace the reader controller PCB.

In any case if you are the end user I sudgest to contact a tech.

Have a nice day.

May 06, 2015 | Canon Printers & Copiers

2 Answers

My canon printer mf4020 display system error e225 on the printer display. what can i do?


E225 means you need to replace the scanner lamp.Unzip the scanner and change the scanner lamp.If a have been useful please give me a vote :).Thanks

Apr 14, 2011 | Canon i-SENSYS MF4140 All-In-One Laser...

1 Answer

We have a Canon MP90 microfilm reader/printer. It works as a reader. However, it won't print. There is a code flashing on the front "P1". What does this mean? I have checked the toner...


the problem is the machine is not feeding paper. need to clean or replace the feed rollers. i have seen this happen quite a bit. the rollers are the same as a canon pc-6 copier and you can order them from PRECISIONROLLER.COM

Feb 22, 2011 | Canon Printers & Copiers

1 Answer

I have machine canon 6030 np and there problem called : E224 please send how can I solve it


Basicly, a E224 is a scanning lamp error code. Here's a question for you??? Will the scanning lamp turn "ON" at all? If so, then the problem is with the scanner power cable. If the lamp will not turn "ON" you may have a blown lamp & or thermal fuse on the scanner unit. You can not clear the code until the problem is fixed. Good Luck

Feb 16, 2011 | Canon NP 6035 Copier

2 Answers

Sir, my canon ir 400 machine shows an error code 803. how can i solve the my problem. give detailed information to my mail. thanking u.


the code 803is for faulty exposure lamp or fault in composite power supply(the power supply to exposure lamp is not sufficiant to operate the lamp).to remove exposure lamp, remove copyboard glass,remove back cover ,slide scanner in the line of rear exahaust fan at the right side of scanner, remove rear exahaust fan, remove lamp holder(one screw).slide out lamp on the rear side replace new one and reverse the whole process.

Jan 27, 2011 | Canon imageRUNNER 400S Copier

1 Answer

Support for error codes


14, NP112, PC3 Код ошибки Описание E0 Heat lamp E2 Scanner
Canon 210, 300 Код ошибки Описание E0 Heat problem E1 Sorter E2 Scanner E4 Drum drive E5 Lens drive E6 Exposure lamp E7 Mirror sensors
Canon 25, 250, 270, 350 Код ошибки Описание E0 Thermistor/thermoswitch or heat lamps E1 Sorter E2 Scanner home E3 Scanner return E4 Right front door/main motor E5 Lens home E6 Lamp regulator E8 Counter wire
Canon 400, 500 Код ошибки Описание E0 Fuser E1 Sorter E2 Scan home E3 Scan E4 Clock pulse or open RF door E5 Lens position E6 Exposure lamp, fuse 2 E8 Counter
Canon 5L, 5ll, 5Lll, 3ll, 2L, PC-1, PC-2, PC-5 Код ошибки Описание E0 Heater problem E1 The heater film has gone off center. Turn machine off & on, make sure it's level etc. E2 Scan problme E6 Exposure lamp or exposure lamp sensor
Canon NP1215 Код ошибки Описание E000 Low temperature, thermoswitch, thermistor or AC driver E001 High temperature, thermistor, AC driver E030 Counter E202 Scan not returning home. Scan not leaving home E221 Lamp regulator board E400 Document feeder problem E500 Sorter problem
Canon 150 Код ошибки Описание E0 Thermistor, thermal switch, heat E1 Sorter, scanner home E2 Motor, clock pulse E3 Scan problem E4 Lens home E5 Lamp regulator/document sensor E6 Motor control E7 Total counter E8 Lamp regulator E9 Copyboard drive motor/board ED Motor control PCB EE DC controller on motor E001 High fuser temperature. Shorter fuser thermistor E030 Total counter disconnected or open E202 Scan problem E210 Lens problem E221 DC power supply, lamp regulator board or main board E400 Document feeder board problem E500 Sorter board problem E000 Low fuser temperature
Canon 1500 Код ошибки Описание E001 High fuser temperature. Shorter fuser thermistor E030 Total counter disconnected or open E202 Scan problem

Jan 19, 2010 | Printers & Copiers

1 Answer

Canon Microfilm Scanner 400 keeps scrolling forward


Canon ms 400 500 Service Manual
generic%20service%20manual%20pic.jpgIf you are having any form of technical difficulty a workshop service manual, parts catalogue, user manual or setup guide is usually the best place to find the help you need. Featuring descriptive photos and text, our range of manuals help you solve a<...>
Details

Price: 4.95 GBP Platform(s): Misc Updated: 19.05.2008 this is the only place which had a manual, either buy it and try to fix it or call canon customer support for addvice.........sodeep

Jun 08, 2009 | Printers & Copiers

6 Answers

Canon ir 330-400 copier


it is supposed to use a separate scanning board (Interface Board-D1) with SCSI connectivity and TWAIN software.

Mar 15, 2008 | Canon imageRUNNER 400S Copier

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts

kakima

Level 3 Expert

96518 Answers

old marine
old marine

Level 3 Expert

1464 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...