Question about Nintendo Wii Console

3 Answers

Wii fit board wont sync

My new wii fit board worked great for two days, now when promted to put the board on the floor and push the power button nothing happens. Tried using the red sync button, unplugged the control unit and replaced the batteries but nothing helped. Any suggestions?

Posted by on

  • 1 more comment 
  • grifrace Jan 01, 2009

    I am having a similar problem but I have had the wii fit board since August and it has worked great. I have not used it in December and when I went to use it this morning I put new batteries in it and it just flashes blue and won't stay on long enough to read. Hope someone can help.

  • lara282 Feb 04, 2009

    I have the exact same problem, I havent played on it for 3 months and when I went toplay today, the power on button just flashes blue. Brand new batteries tried plus fully charged ones. Both in the remote and the bord. Im stuck can anyone help.

  • wiiexpert May 11, 2010

    This is really very frustrating when you face such kind of problems. You may check out Wii Fix Guide
    to fix the problem yourself. This DIY guide will show step by step
    pictures to fix the problems yourself without any technical knowledge.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Ok I feel a little silly, there is a sync button on the console (inside the flap by the power on button) and the board (inside the battery compartment on the underside of the board) as soon as I pressed them at the same time it worked. Goodluck everyone.

Posted on Feb 09, 2009

  • lara282 Feb 26, 2009

    I have posted the solution above, there are TWO SYNC buttons, one on the console next to the power on button and one on the board where the batteries go inside. Press both and it works no need to replace batteries unless of course they have run out!!!!

×

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

After I posted about my wii---my husband unpluged everything and re-synced (spelling?) everthing again---remotes too. Put new batteries in the board first before syncing---and then it worked fine and has been ever since. Thanks

Posted on Jan 05, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a wii fit board that the power button won't stop flashing I have tried to reset the sync button changed batteries twice still not working.

Posted on Jan 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My wii fit board will not turn on it is new please help


Steps:
  • You need to make sure game is in first
  • push power than blue light will blink
  • after the light finishes blinking and still does not turn on then do sync procedure
  • open the battery side and push the red sync button then quickly push the sync button on the wii and wait for it to blink and light should be on

Mar 05, 2011 | Nintendo Intec Nintendo Wii Fit Action...

1 Answer

New crown compatible wii fitness board will not sync with wii console. board only blinks a few times then switches off


Have new crown compatible fitness board, new batteries inserted, inserted Wii fitness disc, choose training, then trial, choose hula hoop game, used remote press A to start.

Screen says place me on a flat floor and press POWER button before stepping onto me

Followed the instructions power button flashes blue, as do the four corners then the lights go out - then nothing happening, still have the same message place flat on floor etc....

Have also tried the Wii Balance Board Check - followed all instructions last one says please turn on power. Pressed button flashes blue as do four corners then they go out

Am I doing something wrong or Is this a faulty board ?

Thanks

Sep 27, 2010 | Video Game Consoles & Games

1 Answer

I have just put new batteries into my wii fit balance board and now it will not power on


Is the light flashing when you push the button? you could try syncing the balance board by holding the red button where you put the batteries and holding the red button on the front of the wii. If the light doesn't turn on at all, I don't know :(

Jun 24, 2010 | Nintendo Wii Fit for Wii

2 Answers

How do i fix my Wii Fit so it will turn on?


try pressing the red butten on the wi console and then take the wii fit board and open the part where you put the batteries in and press that little red butten on the side and it should work:)

Nov 07, 2009 | Nintendo Wii Fit - Balance Board + Game...

1 Answer

Can you tell me how to get wi fit board working


Open the front cover on your Wii, then push the red button there, then open the batteries cover on your Wii Fit and push the red button there.When the board is sync put the wii fit disc in console and follow the instruction.

Nov 04, 2009 | Nintendo Wii Fit - Balance Board + Game...

1 Answer

My wii fit board wont switch the blue light flashes then goes off


Unplug the AC adapter on your console out of the Power cord then wait 15 min and plug it back again.Open the front cover on your Wii, then push the red button there, then open the batteries cover on your Wii Fit and push the red button there.If this not help press and hold the red button on your Wii for 20 seconds.This will clear all synced Wii Remotes from the console.Then repeat the procedure again.In this case you need to SYNC your Wii Remote too.If this not help your Wii Fit may need service.

Nov 03, 2009 | Nintendo Wii Fit - Balance Board + Game...

1 Answer

Wii fit balance board wont connect


Unplug the AC adapter from power cord then wait 10 min and plug it again.Open the SD Card slot cover on the front of the Wii console, just below the disc drive, and press and hold the red SYNC button for 15 seconds. This will clear all synced Wii Remotes from the console.Then push the red button again, then open the batteries cover on your
Wii Remote and push the red button there.After that push the red button on console one more time, then open the batteries cover on your Wii Fit and push red button there.If this not help may your wii fit need service.

Nov 02, 2009 | Nintendo Wii Fit for Wii

1 Answer

Wii fit board - blue power light flashes then goes off and wont work. This is also happening to my parents one and we are both on our 2nd wii fit board each. Have reset red button but no joy - help please


Unplug the AC adapter from power cord then wait 10 min and plug it again.Open the SD Card slot cover on the front of the Wii console, just below the disc drive, and press and hold the red SYNC button for 15 seconds. This will clear all synced Wii Remotes from the console.Then push the red button again, then open the batteries cover on your
Wii Remote and push the red button there.After that push the red button on console one more time, then open the batteries cover on your Wii Fit and push red button there.If this not help may your wii fit need service.


Nov 02, 2009 | Nintendo Wii Fit for Wii

1 Answer

Wii fit board wont sync


get a new board or get it fixed,
try different batteries
dont put any unessessary weight on it
dont stomp on it or jump
be gentle with it
get a new peice so no re-scyn
make sure its not too close too the wii

Apr 11, 2009 | Video Game Consoles & Games

2 Answers

Wii remote wont work after installing wii fit


From Nintendo:
  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

  2. Turnthe power of the Wii console ON. When you see the Health and Safetyscreen, open the small flap on the front of the Wii console to find ared button labeled "SYNC." Press and hold the SYNC Button down for 15seconds. This will clear all the syncs on the Wii, allowing you to geta clean start to begin the process described below.

  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

    1. Withthe first Wii Remote you wish to sync, remove the battery cover on theback of the Wii Remote to find a small red button just below thebatteries.

    2. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

    3. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

    4. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
    5. This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.

Jan 02, 2009 | Nintendo Wii Console

Not finding what you are looking for?
Nintendo Wii Console Logo

811 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles & Games Experts

Bee Santiago

Level 2 Expert

268 Answers

Raj Patel

Level 3 Expert

892 Answers

phil

Level 2 Expert

567 Answers

Are you a Nintendo Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...