Question about TV Receivers & DVRs

1 Answer

RCA 27V412T I have an RCA 27V412T that randomnly turns itself on and off. I have dissassembled the tv and all of the boards attached to power/channel/volume buttons appear to be in good shape. Is there something cheap I need to simply replace to cure this problem. I very much appreciate any help you can provide. Thank you, Mike

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers

Check your tv's power cable inside the tv. make sure its not frayed. also take the batteries out the remote, it could be turning off the tv.

Posted on Jan 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bell expressvu receiver


If you are using the OEM Bell remote to control your Bell receiver, the remote may have failed.

Jan 17, 2014 | TV Receivers & DVRs

1 Answer

Good afternoon, i have a 27 inches ferguson TV and it only ask to select languages but now i don't have a remote what can i do for it to work ?


You might be able to select menu options using the channel up or channel down button on the tv itself. If this doesn't work, try the volume up and down buttons.

Feb 28, 2011 | TV Receivers & DVRs

1 Answer

My tv is a model 27v412t, and i was trying to put the closed caption manually since I lost my remote control and ended up blocking it. At the screen appeared Block on, I tuned off and now it wont turn...


Hello mar...... You will have to either find the remote or replace it as it is the only way to get into the closed caption menu. If you want a replacement factory remote you can go on line at http://www.replacementremotes.com/

Joe
thanks for choosing Fixya!

Jan 05, 2011 | RCA TV Receivers & DVRs

3 Answers

Low volume on Direct TV channels


This is a known and ongoing problem with Directv since June. They claim they are trying to "level" all the channels so they are the same volume level. The result so far is that ALL channels are suffering from low volume. Given this has been going on for two months now, Directv may never solve this - General ineptitude - denials - but if you call and tell them you are having low volume, they will give you a three month $5 credit. CALL and COMPLAIN... the only hope we have to get this fixed is to cost them money and time on their customer support lines.!!!!

Jul 20, 2009 | Directv H21 DTV Receiver

1 Answer

Locked channels on a tv


You need to replace the eeprom IC in your set. Hospitality tv's ( i.e. hospital,motel etc...)have a eeprom IC that restricts programming and the use of the menu so guests can't mess up the tv picture or get unauthorized programming that they want you to pay for or just don't offer more than 27 channels. I have done this for customers before. The eeprom IC is an 8-pin IC that is right next to the microprocessor and is easy to change. Be careful soldering on an RCA board though...too much heat will lift the solder pads.Good luck!

barneyluc

Oct 10, 2008 | TV Receivers & DVRs

1 Answer

How do i program my remote


1. TV on.
2. On your Dish Network remote PRESS AND HOLD the small clear tv button until all buttons across the top of the remote light up and release.The only button lit should be the clear tv button that will be flashing.
3. Press the small red tv button next to the power button and release it. This should leave the clear tv button that was flashing lit solid.
4. Now slowly depress the channel up key until the tv turns off.Each time the up channel button is depressed the clear tv button will cease being lit and once it is released the clear tv button should remain solid. If the clear tv button flashes multiple times it usually means there is no known code for your tv, there may be another code that will work so continue on.
5. Once you are successful in getting the TV turned off press the channel down button once and then the channel up button. This should turn the TV back on.
6.Press the # key button on the remote. The clear tv button should flash three times then press the record button and try the volume up/down and the small red tv button. You should be able to turn volume up and down and turn tv on /off. If only one of these function it means that you have only found a half code and need to try the process again. Not all TV's have full codes or any codes at all especially combo units.

Aug 25, 2008 | RCA DISH Network(r) 311 Satellite System

1 Answer

Digital TV Converter keeps shutting off


The DTA800 has a Power Saver feature that turns the unit off after 4 hours if it is idle (no volume or channel changes).

Press MENU button, press #5 (Setting/Configuration), press #3 (Power Saver) Select OFF to de-activate this feature (no Power Saver).

This is covered on page 11 of the DTA800 user manual.

Apr 25, 2008 | TV Receivers & DVRs

6 Answers

Dish network hd monitor


Did you get a resolution to your problem? I am having the same situation.

Oct 28, 2007 | TV Receivers & DVRs

1 Answer

Tv wil not change channels unless vcr is on


You must go into the menu, go to the channel setup and do a channel scan.. Your TV simply lost the channel memory. Good Luck

Aug 16, 2006 | RCA 6' Video/Optical Combo Cable -- DT6VHP

Not finding what you are looking for?
TV Receivers & DVRs Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top TV Receivers & DVRs Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

68368 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18304 Answers

Are you a TV Receiver and DVR Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...