Question about Westinghouse WST1500 Wired Special Edition Upright Vacuum

1 Answer

How do I remove the housing cover on a westinghouse vacuum?

Upright vaccum model wst 1551

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Remove clear snap-in lights lens. Remove both lightbulbs. Where the bulb sockets are there is a screw, remove them. Then simply pull up on the housing from the rear where the wheels are and remove the top cover.

Posted on Jun 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Panasonic optiflow upright vaccum


Hello, Put the vac on its side and remove the screws holding the cover plate on. This exposes the beater bar and belt on the side. Pull the beater bar out and take the belt off. Reverse this to put the belt back in place.

May 30, 2014 | Panasonic MC-UG323 OptiFlow Upright Vacuum...

1 Answer

I need vacuum cleaner bags for a WST 1300


call a vacumn or small appliance repair shop most vacumn repair shops will know what bags you need esp if they service your model or may be able to tell you who to call

Dec 18, 2009 | Vacuums

1 Answer

I have a Eureka Bravo! 7.0 vaccum cleaner, how do I change the belt


Turn the vac over so the brush is facing up.. There is a cover plate that surrounds the brush.. Take the screws out and remove the cover plate.. Pull up on the side of the brush that the belt is on.. Replace the belt.. The belt goes around the metal shaft and the brush.. Push the brush back in place.. It might be a bit tough going in because the belt causes some tension.. Put the cover plate and screws back in..

Good luck ! Please don’t forget to rate well ;o)

Aug 14, 2009 | Eureka Altima Upright Vacuum Model 2996AVS...

1 Answer

Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal...


You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new belt on the chrome axle. Then put the brush on, rapping the new belt around the brush as you put the brush back in place.

Jim

Jun 09, 2009 | Dyson DC14 All floors Bagless Upright...

1 Answer

Eureka Vaccum Tripping Breaker While in Use


ur overloading the circuit in the house try turning off everything that is on that surcuit i mean everything then see if the vac works

Apr 04, 2009 | Eureka 4700A Maxima Bagless Upright Vacuum

1 Answer

Eureka altima stopped power mid vaccuming, have changed outlits


make sure all your filters are clean,try to turn the brush roller by hand a few times if it turns real freely then the belt is broke.if it is reall hard to turn then you have something wrapped around the ends of the roller where the bearings are.your motor guard might be keeping it from running because it got too hot take the brush roller out and the belt let it cool down for 20 minutes then try it without the roller and belt.you should be able to take the ends of the roller off by just pulling out on them so you can remove what ever is in there

Mar 21, 2009 | Eureka Altima Upright Vacuum Model 2996AVS...

1 Answer

Prices on Westinghouse WST1550 vac parts 40008 & 40020


i need a new bin filter mine smells like mildew i washed it like it said and it now stinks.

Jan 25, 2009 | Westinghouse WST1550 Wired Deluxe Upright...

1 Answer

WST 1600A


It sounds like there is a clog. If there is no air flow it could be overheating.

Feb 23, 2008 | Westinghouse WST1600 Upright Vacuum

1 Answer

How do I open the vacuum assembly?


you have to take the headlight lenses off with a small screwdriver. then a philips screwdriver to take the 2 screws out. one each side. then remove the foil shields on each headlight . then snap loose the rear plastic clips on the cover and it will come right off. it took me an hour to find out how and 10 minutes or less to take it off. watch for the micro switch on the circuit board being worn out.it will stop the roller brush from turning.its a dollar part at any good electronics store ,but will have to be soldiered in or service might have a few from the westinghouse line .so will a broken belt which is a special grooved belt available from fantom at 18007987395..

Jan 11, 2008 | Westinghouse WST1550 Wired Deluxe Upright...

1 Answer

Replace belt


On the bottom, there should be a few screws to remove to remove the plate covering the brush roll. However some may have screws on the top housing to remove the top.

Jan 06, 2008 | Vacuums

Not finding what you are looking for?
Westinghouse WST1500 Wired Special Edition Upright Vacuum Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Westinghouse Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

AskDyson
AskDyson

Level 3 Expert

2572 Answers

Roger Potts

Level 3 Expert

694 Answers

Are you a Westinghouse Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...