Question about InFocus ScreenPlay 7205 Multimedia Projector

1 Answer

Smalll Picture I have an InFocus 7205 projector with a Marantz SR 7400 projector with a New Panasonic Blue Ray VCR. The picture size is very small, about half what my DVD player produces with same setup. I tried a Sony Blue Ray and had the same effect.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 167 Answers

Hello,
In the projector's menu under "aspect ratio" is sounds as though you have it set to "native"
this setting usually results in a small image.
Try either the 16x9 or the 4x3 setting depending on the aspect ratio of the source. I hope this helps you.

Cheers

Posted on Dec 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my projector Infocus 7205 says constantly replace lamp and we have a new lamp? Thanks for helping...


Hello,
On the projector you will see 2 buttons for adjusting the brightness, with the projector on press both the brightness up and down at the same time.
Hold them both pressed for 10 seconds. This will reset the lamp timer.

Take Care!

Nov 13, 2009 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

The start up screen is on with no signal through


Try a firmware upgrade.

http://www.infocus.com/Support/Products/Projectors/IN76.aspx

Oct 24, 2009 | InFocus Play Big IN76 Multimedia Projector

1 Answer

My Infocus ScreenPlay 7205 has vertical lines throughout the whole picture when in use. Only about 1300 hours on the unit.


This could be an issue with the projector but here are some possible other causes.
1. make sure the wires running to the unit are not by any power source or other elctronic devices as this can cause interference.
2. use a differrent input source to check if the lines remain. (cable/satellite, dvd player, camcorder). if it does than it is most likely the projector.
hope this helps

Oct 18, 2009 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

Infocus projector


The settings of the video section of the computer probably need to be adjusted; this is a synchronization problem.
Check the Infocus website for clues.

http://www.infocus.com/Support.aspx


May 27, 2008 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

Infocus Screenplay 7205 Projector


Hi there

It might be a small IC that has gone on the Powerboard , I wouldn't worry about it if I were you.

Apr 14, 2008 | InFocus ScreenPlay 7205 Multimedia...

1 Answer

Infocus Screenplay 7205


losing signal. reset the setting to factory default. adjust the clock and phase, too.

Jan 06, 2008 | InFocus ScreenPlay 7205 Multimedia...

Not finding what you are looking for?
InFocus ScreenPlay 7205 Multimedia Projector Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Multimedia Projectors Experts

Juan Carlos Pacheco

Level 1 Expert

36 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

Are you an InFocus Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...