Have a medion 96820. How do you shut off the Speed limit prompt that repeats every two minutes? also, do not see a volumte control. Is there one?

https://diy.stackexchange.com/questions/130130/furnace-runs-for-about-5-minutes-only-and-shuts-off?rq=1
Why does my furnace run then stop? A common reason a furnace short cycles is because the heat exchanger, the part that heats your air, is getting too hot due to a lack of airflow. Once the heat exchanger overheats, it trips the high limit switch, which shuts the furnace down to protect it.Dec 9, 2016

If you know how to set your speed limiter. To set your cruise control, press the stalk in (to the right). The orange light on your dash should go out and you're ready to set your cruise control. You can start the cruise control by either moving the cruise control stalk up or down. Once you start the cruise control you can move the stalk up or down to increase or decrease your cruise speed. You can move it toward you to shut off the cruise control. You can press it in again to go back to the speed limiter. I hope this helps.

probably high limit some are adjustable.

When start-up prompt "PRESS ENTER TO BEGIN OR PRESS QUICK
START" appears, access the Club Program by sequentially pressing
STOP, SPEED , SPEED , SPEED , RESET, SPEED , SPEED , and
SPEED . (Numbers on the display appear in sequence: 4, 5, 6, 5, 1, 5, 6,
and 5.)
Note: You must sequentially press each key within 4 seconds of each other
or the display reverts back to the start-up prompt.
6. Maximum Speed: Use any or key to designate a speed limit between
1 and 15 mph (1 and 24 kph). The speed you designate limits the speed of
the treadmill. Press ENTER when the desired speed appears.
7. Maximum Workout Time: Use any or key to designate a time limit
between 10 and 240 minutes. The amount of time you choose limits the
length of a person's workout. (This does not include the automatic 5-minute
cool-down period.) Press ENTER to accept the time limit.
Note: Continuous pressure on the arrow key lets you scroll through the
numbers being displayed.
8. Language: Use any or key if you want to change the language. You can
choose between English, German, Spanish, or French. When you change
the language, you affect all the prompts and informational messages that
appear on the display. Select the language being displayed by pressing
ENTER.
9. Custom Courses (C964i only): The course profile appears in the center
display. (If you want to customize course number 2, press ENTER.)
When you enter custom mode, you have the ability to "draw over" an existing
God bless you

This is the speed limit control and set to off does into i-drive menu/setting/car setting/speed limit.

It is rare that a limit switch goes bad. It is a safety control. If it is shutting off your furnace there is a problem that it is protecting you from.
If the limit switch is shutting the unit down your furnace is overheating. Check the filters. Check for any obstruction in the blower assembly. Check to see if you can raise the blower speed. Make sure all registers are open in the house. Your evaporator coil could be obstructed if you do not take good care of your filters.

I got mine last night and all works fine - even though I had to disconnect it and reconnect it to see the internal memory content (preloaded) on the flash drive of the GPS. Once I saw the maps and other data, the Drag & Drop of MP3's worked as expected (using XP). I set up Active Sync as a guest account. Love the unit so far. Easy to use and fast response.

Medion MD 96015 Notebook shuts down. Other searches you may want to try:

• Medion MD 96015 Notebook
• Notebook Medion Microstar
• Aldi Medion Notebook Reviews
• Medion Notebook 96015
• Medion Notebook Computer
• Gateway Notebook MD 3450
• Medion MD 96015

If Computer runs Hot or Shuts down for no reason:

Repair4Laptop: How to Repair the Cooling Fan of a Laptop or Notebook

t

What's your OS? Win XP, Linux...what? If those are installed correctly, they should automatically find the drivers or prompt you to put in the software disk for it. If WinXP Go to Control panel > System > Hardware Look for any "yellow !" and remove them. Shut down and restart. Should solve your problem.