Question about Air & Gas Compressors

1 Answer

My phone keeps rejecting bluetooth files lg kg800 bluetooth not working

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 70 Answers

You should rewrite this question under phones it is under air compressor forum hope this helps

Posted on Jan 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I own a stanley pressure washer and it keeps tripping out


The pump will cycle on/off but if it works properly when you pull the trigger and it keeps working then its working correctly.

Jul 20, 2014 | Stanley Air & Gas Compressors

1 Answer

5 amp fuse keeps blowing


Hi Jeff,
The fuse is to protect the blower, you and other equipment. It is a warning that something is not working correctly.
If you have a multimeter, use it to see if you have a short circuit or a partial short circuit by using the ohm measurement.
Physically check the wires and and wire connections in the unit to see if there is any sign of shorting out - usually looks like a black smudge.
Do not replace the fuse with a higher rating fuse.
If you can find some short circuit, thoroughly clean the area, or replace the faulty wire, or both.
If you cannot find a fault easily, you may have to get the unit seviced.

Jan 30, 2014 | Air & Gas Compressors

2 Answers

I have a vt631401aj campbell hausfeld compressor. when it builds pressure to 135 psi, the compressor shuts down and immediatly starts dumping air until it goes down to 90 psi. It then stops dumping the...


John: I had a similar problem with a brand new CH-made compressor. The problem was not with the unloader valve, but with the check valve located where the air from the pump enters the tank. The check valve was not seating correctly due to brass filings from manufacture. The defective check valve was allowing air to escape back the wrong way from the tank to the pressure switch and through the unloader valve. This backflow from the tank would start to happen when the pump stopped after reaching high pressure. The back flow would continue until the pump restarted at the low pressure point. This cycling would continue as you described. Once I cleaned the check valve, everything (including the unloader valve) started working correctly. I hope this helps. And remember, don't work on these when they are under pressure and always wear safety glasses.

Sep 18, 2011 | Campbell Hausfeld Air & Gas Compressors

1 Answer

My LG fridge does not cool and the compressor is not working but the system power is on


Hi,

Many times a freezer and/or refrigeratordo not work right because of a dirty condenser coil...there are also many otherthings that can go wrong. If you are hearing a clicking or buzzing thencheck out the last two tips.

If your refrigerator is running but warm, then...

Check out these tips that I wrote about that... it is a great place to starttrouble shooting your unit...and something that you can do rather then callinga repair person to do a simple thing for you...

Refrigerator Condenser Coil Cleaning Refrigerator Repair

Refrigerator Troubleshooting Refrigerator Compressor

Refrigerator Compressor Start Capacitor and Start Relay
Refrigerator or Freezer not Cooling or Getting Cold

heatman101


';';

Jul 17, 2011 | Air & Gas Compressors

1 Answer

The valve on the bottom of the tank broken off


Lay the commpressor on its side so you can get to the bottom. You may be able to take a file and drive the tang in to the broken fitting and use a wrench or pliers to turn the file and remove the broken fitting. If this doesn't work, go to the parts house and buy and buy a screw extractoe or ezy out.

May 19, 2010 | Air & Gas Compressors

1 Answer

My compressor charges up to 60 PSI. It keeps on running but will not charge over 60PSI. I feel or see no leaks. Why?


Reed Valves in cylinder head. Pull head off and order Valve Kit through Campbell Hausfeld. Phone number etc is on internet.

Apr 27, 2010 | Campbell Hausfeld 26 - Gallon Air...

1 Answer

MY COMPRESSOR JUST KEEPS RUNNING AND WONT REACH MAXIMUM PRESSURE AND SHUT OFF. I CAN SHOOT NAILS BUT IT WONT SHUT OFF DOWN.


The compressor itself sound like it is bad. You might see what it cost to repair it. It might be cheaper to get another one...keep in mind if you do a lot of work with it that a 2 stage compressor will cool better and you won't have this type of problem again.

Oct 19, 2009 | Craftsman 1 Hp, 4 Gal. Air Compressor

1 Answer

Craftsman 3.5 hp portable air compressor keeps blowin head gasket


I would say the head or block is warped. Use Majic Marker to cover the mating surfaces , the head can be rubbed on a flat surface like a cast iron table saw to find the high spots, or the head can be rubbed on the block.
Careful work with a good flat file will remove the high spots.
The torque value sounds low even for an aluminum block, you could check with a small engine shop to get their opinion.

Apr 25, 2009 | Craftsman Air & Gas Compressors

1 Answer

Compressor wont run unless I cover the air intake where the filte


Most compressors have an in-tank check valve that prevents pressure in the tank from loading the compressor and forcing the motor into overload. The pressure switch also has an unloader that releases pressure in the system so that the motor will not strain when it recycles. When you restrict the intake, the compressor is unloaded thus the motor will continue to run. There may be a problem with the checkvalve or the motor may have a weak or failed capacitor. Some meters have a capacitor test to check if the capacitor is the problem. Reject the capacitor it it tests out of range more than ten percent. enjoy

Nov 28, 2008 | Chicago Pneumatic Air & Gas Compressors

1 Answer

Electric motor stalls


A compressor can stall before completing a cycle if the motor is not receiving correct power, such as when there is an extension cord being used or outlet is overloaded with other appliances. Other problems that cause this condition are in-tank check valve is leaking pressure back to the pump and weak or failed capacitor. Some volt meters have setting for checking caps. Reject the capacitor if reading is 90% of rated value. Rare problems include worn bearing or bad contacts on pressure switch. enjoy

Nov 05, 2008 | Campbell Hausfeld 20 - Gallon Air...

Not finding what you are looking for?
Air & Gas Compressors Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Air & Gas Compressors Experts

John Trevino

Level 3 Expert

1378 Answers

JOHN LAPIER

Level 3 Expert

2386 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Are you an Air and Gas Compressor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...