Question about Kenmore 24032\24036 Top Load Washer

1 Answer

No power i have a kenmore washing machine calypso is the model it tiped over and i can't seem to have it on . i've cleaned the pump and all the hoses.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Ok lets get you started,,im grinding,,you leaned your unit over to change pump and it fell down,,,ok work with me here...you pull a connection out ,,since there no power you have no codes,,,hummm...unplug unit than take back console cover and push in on all connection,,im here reply when ready...

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore elite washing machine with calypso - cycle ended with water in tub after partial wash of 3 towels, signnal was LD - re-started machine and it stopped with signal FL - machine will not re-start


Fl stands for flooded. Either your pressure switch is bad or plugged in the tubing from the tub to control panel or the sensor is bad. But check and make sure the water is draining or pumping out like it should, if not the problem may lie in your drain pump or hose.

Mar 13, 2011 | Kenmore Washing Machines

2 Answers

What does the Ld code mean on a calypso Kenmore Elite Washing Mashine


Hello there
LD means a long drain
it is taking longer than 8 minutes to drain out the tub
please check the following
First unplug the machine to prevent electrical shock·
Check wiring harness to ensure they are all connected and are not fried
·If needed remove the side panel and Check the hoses going to pump for clogs and all drain hoses and drainage system
· Check circuit board that controls the pump to see if any wires are burnt or have failed
once the faulty part or the clog has been cleared simply plug in the machine and press the cancel button and resume your normal washing operation
Hope this has been very helpful for you
Best regards Michael

Dec 30, 2009 | Kenmore Washing Machines

2 Answers

My Kenmore Calypso Elite HD Top Loading washer quit cycling through a complete wash today. I've drained all the water from the interior hoses and found them clean and uncloged. The washer belt looks good...


skipneal,

The code on your machine stands for 'Long Drain'. Ld flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets. Check the intake and exit hoses of the recirc pump for debris. It's easiest to get to the pump through the front panel of the machine(click here). Looks like this: click here. the hoses to the pump have spring clips holding them on. Be careful taking the hoses off, have something to catch the water from the hoses.

Hope this helps.

-samson39

Jul 20, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

How to remove the cap on Kenmore Elite Calypso washer


you'll need to access the pump and remove the hoses. Clean the inlet screen.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Mar 16, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Kenmore elite calypso model 11022086


FL means flood condiction..clean or replace your pump..

Jan 09, 2009 | Kenmore Elite 45986 Front Load Washer

2 Answers

Calypso washer won't spin and drain properly


i've pulled stuf from many a calypso pump and its not the funest pump to clean.some designs never get stuff in the pump others its like theres a sock magnet in there or somthing.your has got a sock magnet.take off the frount and you will see the pump on the right.white,it has two hoses.take the inlet off first if eazyest then will only have to take one hose.you can geter done.God bless,tom

Jan 03, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

I have kenmore elite calypso wash motion washer and there is a flashing light the reads FL what does this mean.


flood lock you need to drain all water from machine and clean out pump somethimg cloggimg pump

Dec 08, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Calypso 22066 top=load washer


You probably have hoses and sump pump plugged/jammed by not enough to the machine from operating, my machine leaked prior to cleaning out all the hoses and sump pump

Aug 29, 2008 | Kenmore 22062 Top Load Washer

1 Answer

Removing the outside case on my kenmore washing machine


have you tried just leaning the washer back ?? if that is not a calypso the bottom is card board and just pulls down pump is on front end of motor 2 clips 2 hose clamps ..if calypso remove screws in bottom pump back right corner as far back as i can remember all full size top load kenmore washer pumps were accesible from bottom that's 35 yrs by the way

Jul 17, 2008 | Kenmore 24932 Top Load Washer

Not finding what you are looking for?
Kenmore 24032\24036 Top Load Washer Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...