Question about Nyko Charge Station for Nintendo Wii

1 Answer

Blue lite for the controller charging cradle is always on

The bluecharge lite always stays on

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

It stays on so you know it is charging.

Good Luck and Please Rate FixYa!

Posted on Dec 28, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Good afternoon, I´m trying to


Have you tried:

http://plantronics.custhelp.com/cgi-bin/plantronics.cfg/php/enduser/std_adp.php?p_faqid=8165&p_created=1128461658
I was searching for this today and happened to find the above on the plantronics website. It definitely frustrated me till I found out about how to put the base in pairing mode.

Jan 03, 2011 | Plantronics Voyager 500A Deskphone Adapter...

1 Answer

The charger/traffic receiver glows green but it does not charge the unit. How can i test whether the fault is a, the charger, b the cradle or c, the unit


hi,

1st of all let me say im on my 3 cradle now for my 760 because the connection inside the cradle where it mounts to the board is pretty poor.

since you said the traffic/charger has the green light lite, that means the charging part of it is working.

you can verify if its the cradle or the connection on the bottom of the gps where the cradle mounts by using the usb cable supplied with your garmin.

plug it in for a while, then check the battery meter after you unplug it..if its charging, the meter would have risen beyond what it was before you tried to charge it. the same can be done with a regular garmin charger (the one that uses the usb connection for the car charger to charge it)

bill

b4e1765.jpeg

Apr 12, 2010 | Garmin (010-00583-00) for nuvi 750/760/770

1 Answer

Wont charge ....just shows colors and low battery icon


1) Ensure the cradle is plugged into an active AC outlet and the LED light on the cradle is on. There is a switch on the bottom of the cradle to control the brightness of the LED, set it to the highest. Try different outlets if needed. Does the LED light turn on and stay on (does not blink)?
ANSWER:
2) Remove the battery. Place the remote on the cradle and check the LCD screen. The LCD screen should display a 'White' screen with possible colors before going off. Try this a few times to confirm behavior. Did the LCD turn on briefly?
ANSWER:
3) Reinsert the Battery. Have you charged the battery for at least 3 hours? If no, please recharge the batteries for at least 3 hours.
4) Did the battery ever boot the remote? If yes, please continue troubleshooting.
ANSWER:
5) Remove the battery. Check the 3 gold contacts on the battery to see if there are markings on all the contacts signifying it was connected correctly to the remote. Did the battery have markings on all 3 contacts?
ANSWER:

Jan 16, 2010 | Logitech Harmony One Advanced Universal...

1 Answer

Remote not charging?


the battery can be charged whenever you want to charge it. There may be an issue with the cradle. can you please follow steps below and reply back with the answers?


1) Ensure the cradle is plugged into an active AC outlet and the LED light on the cradle is on. There is a switch on the bottom of the cradle to control the brightness of the LED, set it to the highest. Try different outlets if needed. Does the LED light turn on and stay on (does not blink)?
ANSWER:
2) Remove the battery. Place the remote on the cradle and check the LCD screen. The LCD screen should display a 'White' screen with possible colors before going off. Try this a few times to confirm behavior. Did the LCD turn on briefly?
ANSWER:
3) Reinsert the Battery. Have you charged the battery for at least 3 hours? If no, please recharge the batteries for at least 3 hours.
4) Did the battery ever boot the remote? If yes, please continue troubleshooting.
ANSWER:
5) Remove the battery. Check the 3 gold contacts on the battery to see if there are markings on all the contacts signifying it was connected correctly to the remote. Did the battery have markings on all 3 contacts?
ANSWER:

Jan 14, 2010 | Logitech Harmony One LCD Touchscreen...

1 Answer

Hi. The yellow lite on my ms9353 blinks when I


Contact Honeywell - call 1800-582-4263
They should be able to help you. Have the model number and serial number of your scanner ready.

Cheers

Billy Barcode

Aug 04, 2009 | Metrologic Instruments MS9535 VoyagerBT...

1 Answer

Palm v


the lightning bolt indicates that the battery is being charged. I will stay on as long as it is being charged either in the cradle, or using an external charger. If it stays on after it is removed from any external power source, there is a problem with the unit and it needs serviced.
--Randy Miller

Aug 25, 2008 | Palm TX Handheld

1 Answer

Reset button won't work on dell axim x51v


to wlumbria... hey listenup... if ur connecting ur pocket pc to the cradle it is not only used for the flow of data bt it also charges ur pocket pc... bt the chargin is quite slow  it will keep on showing  the red lite as compare to an charger it will charge fast and the red lite will turn green... so wht i suggest charge it with a charger not with a cradel if stil it doesnt wrk try changing the battery...!!!

Aug 21, 2008 | Computers & Internet

1 Answer

Tom tom rider version not charging via bike cradle either via direct connection to the bikes battery or when connected to an aux power socket. There is also no sound while attached to the car cradle /...


I recently had a bit of success with TomTom. My TomTom Rider 1 did not charge on the bike cradle, there is a known problem with the early cradles. TomTom have developed a TomTom Rider 1 replacement cradle (updated) and if you push hard they will wend you one in the post free of charge.

Jul 27, 2008 | GPS

1 Answer

Just got Verizon 755p - can the power stay on while charging?


Try StOIC (Stay On In Cradle):

http://mytreo.net/downloads/stoic-stay-on-in-cradle,221.html

It's free and it works - the screen will stay on whenever the Treo is connected to charging power (e.g., in the cradle).

Enjoy!

- IntelelctArsenal

Jan 18, 2008 | Palm Treo 755p Smartphone

Not finding what you are looking for?
Nyko Charge Station  for Nintendo Wii Logo

Related Topics:

509 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nyko Video Game Consoles & Games Experts

Josh Whitehead
Josh Whitehead

Level 3 Expert

1148 Answers

yadayada
yadayada

Level 3 Expert

70346 Answers

Brad Brown

Level 3 Expert

15100 Answers

Are you a Nyko Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...