I brought my Roadmate 700 in 2005. About 3 to 4 months it just stop working. It says waiting tempature is to low... It never gets pass that message... So I see this message each time I start my truck.... I have tried waiting all day and the same message tempature is too low... What could it be and What can I do to fix the problem.....
An expert who has written 50 answers of more than 400 characters.
An expert who has written 20 answers of more than 400 characters.
Re: Magellan RoadMate not Working
Common problem Herbert,
Unfortunately, it's a common problem that can be fixed by having several dead units lying around to take parts from. So, if you can find a unit to salvage from, then do that and change out the LCD. if you can't.. then I'm sorry Herbert but there's not much else you can do. Try reloading the software if you have the DVD. open up the unit and make sure all the cables and everything are tight/secure. Good luck.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1. Turn off your printer 2. Press and hold the
STOP/RESET button 3. Press and hold Power ON button 4. While
holding the Power ON button, release the STOP/RESET button 5. While
holding still the Power ON button, press twice the STOP/RESET button 6.
Release the Power ON button 7. Wait until it display an "idle"
message. It will take about a minute. 8. When "idle" appear, open
the top cover to expose the cartridges. 9. Lift up the cover for
cartridge holder and take out both the black and color cartridges 10.
Return the cover of cartridge holder and turn off the printer 11.
Return the top cover and turn on the printer again 12. After the
printer initialize, return the cartridges.
1. Press and Hold the
STOP/RESET button and wait until it self restart. 2. Release the
STOP/RESET button the the printer is restarting. 3. Wait for a few
One thing you should know about a gas oven is that they do not keep a constant tempature like an electric oven does. So going by a tempature gauge in the oven can fool you. The way a gas oven works is by "average" tempature. In other words if you take the highest and lowest tempature readings and average them out you will get the actual tempature. For example let's say that you set the oven to 350. Well first it will take about 10 to 15 minutes for the oven to properly pre-heat. Once it is preheated you can listen to the gas burner and watch a tempature gauge(flook meter is best). When the gas burner shuts off the oven tempature will continue to rise. When the oven tempature stops rising then you will take that reading. Then wait for the oven burner to come back on again and watch the tempature gauge. When the tempature gets to it's lowest point and stops then take that reading. Do this several times and then take all the tempature readings and add them together then divide that number by the number of readings you took and that will give you the actual tempature. Within 5 degrees is great but anything over 10 degrees can affect your cooking. This will give you an idea if your oven is out of calibration or not.
Had the same problem with my MRM 700 back in 2005, only 2 months after I purchased it. They changed the connector, and it worked. BUT, few months later I had the same problem again. I haven't used it anymore since then (moved to another country), now I am trying to fix it but no warranty anymore..
I'm an English guy with the same problem... What you do is keep the power on for a long time, or you charge it up with the charger. Trust me. However, it is very rare for this to occur. There should be a message saying: "Temperature is too low, keep power on." There should be another message reading: "Turn off power and turn on again to check if camera is fully-functional. Thanks for giving me something to do while X-Plane downloads on my Mac OS X.
I had the same problem. At first intermitant and then permanent. The power connector inside the based that the head unit snaps onto had the center post fall out. You need to removed the 4 small screws located in the threaded reseases. Then using a knife I pried the plastic halves apart. You need to break the ultrasonic bonding on the plastic, but everythign seperated where it should. Now you have access to the circuit board. I soldered in 2 wires which I brought our and soldered to a cigarette outlet cord. Then I screwed it all back together.
hah.. yes that is a strange coincedence. When this error appears, you can try to find someone else's unit and use it for spare parts. If you can find another unit to salvage from, then first change out the LCD w/attached thermometer wires. next to change is the hard drive. which, without having the software DVD can't be completed. I'm sorry Jerome but. there's not too much you can do with this error.