Question about GE WSM2700W Unitized Spacemaker Washer and Dryer

1 Answer

Too Much H2o

Weither on low, medium, or high selection for water level......machine will not recognize and fills continuously....Any ideas would be greatly appreciated, thank you

Posted by on

  • mserin Nov 25, 2007

    same unit same washer 3 to 5 years old. Washer over filled and flooded the house.

  • Captn_Kremen Mar 05, 2009

    Machine does not stop filling. As a result it overflows unless water is turned off at supply.



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Either your waterlevel switch is bad or the hose from the tub to the switch is leaking air. more info would do you have to turn the water off at the wall for the water to stop rising or do you just have to push the timer knob in?? let me know, i can definitely help to diagnose!!

Posted on Apr 24, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hello--My Maytag washer LAT8614AAE stopped while filling. It still spins, and stops spinning when top opened. I replaced water valve, so that wasn't the problem. Ideas? Thanks!

I would check the water level switch. It is activated when the water level is as per requested (low, medium, full). It might give the OK to the timer.

Jan 23, 2018 | Maytag Washing Machines

1 Answer

After washing 2 loads the machine won't fill to high level it only fills 1/2 way

You have a faulty fill valve. Return/ replace you washer if under warranty. If not then you will have to replace your fill control valve. That valve is where the knob for the fill level is.

Mar 12, 2014 | Danby 1.7 Cu. Ft. 4-Cycle Portable...

1 Answer

We have a fisher and paykel gw711 washing machine that continues to fill with water while it is in the rinse and spin cycle

Hi Robbie just read your posting.Now just a couple of questions.Does the machine keep filling and flood?Can you manually select the amount of water for the wash --eg-- low, medium,or high?Or does the machine drain and fill at the same time?Please reply with additional information on the questions and I am sure I can rectify this fault for you.

Jul 16, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Water not filling.

r u using auto fill mode?if u r then try selecting high medium or low. check water pressure coming out of inlet hose, could b faulty valve not letting enough pressure thru.please reply if u need more help

Mar 14, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Machine won't fill up. Water just keeps on running.Tried to fill up on low, medium and high to no avail.

Good day,
If it keeps filling, and can't then it sounds as if you have the drain hose positioned too low.
It must reach a point higher than the highest level the water will ever reach.

Jan 18, 2010 | Washing Machines

2 Answers

Maytag FAV6800AWW - Major overflow right after starting machine

Hi, If you turn the water source valve on and water starts filling the machine even tho the machine is off, change the inlet valve.
If you have to start the machine so water will fill but, the water does not shut off at the desired level, there is a problem with the water level switch.
I hope this helps you. Please let me know if I can assist you further.


Jun 13, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag washer water doesnt stop

raise top or remove front panel(can't remember which) rear corner left small hose attached to connector on tub pull and clean probably plugged up with crud also ck connection on tub

Dec 12, 2008 | Maytag HAV3460AWW Top Load Washer

1 Answer

When washer is in super wash cycle water will not stop causingthe tub to over fill running onto the floor.

It sounds like you are trying to use the largest water level setting. If this is correct you may have a pressure switch problem.

First turn the timer to spin and get all of the water out, that start a washer cycle with the water level set to the small or low setting and see if the washer fills to this level. if it stops at the low level great Now if it continues to fill and does stop you may need a pressure switch or the hose needs to be replaced that runs from the tub to the pressure switch.

Now set at the medium level and try again. does it stop or over fill?

If it over fills you probably need a pressure switch however before you purchase this, make sure the hose is in good condition one pin hole will cause your overfill condition.

Jul 09, 2008 | Washing Machines

2 Answers

Washer continuously fills but drains at the same time during rinse cycle.

you have the drain pipe too low into tthe house drain pipe, raise the washers drain pipe up , you only need four inches down into the hous drain

also the house drain pipe needs to be as high as the lid of the machine before you put the washer drain tube into the house drain

you have a syphoning effect

Apr 20, 2008 | Washing Machines

Not finding what you are looking for?
GE WSM2700W Unitized Spacemaker Washer and Dryer Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides