Question about Yahoo YHT-630 System

1 Answer

I need an Epson R265 Reset please

The two flashing red lights indicate the ink pads are full when trying to print on DVD's. This is not the case as the ink pads are unused and bypassed!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

I managed to get a resetter program for the Epson R265 from the USA which did the trick!

Posted on Dec 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Standby indicator flashes


When the "Protection" indicator comes up the display panel of my receiver or the On/Standby LED is flashing, does that mean my receiver needs to be repaired?
The "Protection" light comes on when the receiver's current sensing and thermal monitors detect some unusual operating condition that, if left unchecked, might damage the amplifier. This can happen if there's a dead short in a speaker wire or if you're using very low impedance loudspeakers at high volume for an extended length of time. On older model AVRs you may see the word "Protect" on the receiver's display. More current models will indicate a flashing red light on the Standby LED when a Protection circuit trips
n thermal cases, the circuitry will automatically reset after a few minutes of cool down and the Protection indicator will go out and normal operation will resume. If the protection light came on due to a speaker wire short, low impedance condition or a bad speaker, the receiver's power will need to be turned off to reset it. Before turning the power back on, all speaker wire connections should be checked for their integrity at the receiver side and at the speaker side. If the protection light goes on immediately after you turn on the receiver, disconnect the speaker wires at the receiver side and retest. If the receiver's protection light goes off, then there would still seem to be a problem with one channel's speaker wires or speakers. Connecting them one by one and retesting should allow you to find the problem speaker or connection.
If after checking all your connections, the Protection indicator stays lit, you may need to "initialize the microprocessor (see the FAQ on that topic) or take your receiver to an authorized repair center for a diagnostic. The "Initialization of the Microprocessor" or "reset" procedure can be found in your owner's manual on current model AVR product. Please note, this will erase all setup configurations in the system and require the system to be setup again. You may want to mark down the settings before resetting your receiver to aid in the setup process. If you had an installer setup your system, you can contact them for assistance and any associated costs that may apply to setup the receiver again would be the responsibility of the owner.

Jul 17, 2016 | Sony DAV-FR1 System

Tip

Sony ebook Reader is Frozen, Not charging


The Sony Reader used a special type of display; the LCD can retain an image without having power. It takes power while changing the pages. In most of the cases, if the power is fully discharged, the LCD will keep the last image that was displayed it makes an impression that the Reader is frozen. However, the Actual thing is, the screen retains the last image on the screen and there is no power to change the pages. These type of situations can be resolved by charging the Reader sufficiently.
Each step in my solution is a possible resolution. Hence I suggest thatyou perform each step and check the operation.
  1. Charge the battery fully by connecting to a computer or by using a compatible AC Adaptor. It may take a few minutes (up to 15 minutes) to displaythe charging symbol if the Reader is fully drained in its last use.
  2. Once the reader is charged fully (at least 45 minutes), slide the power button to turn ON.
  3. Perform a softreset. We can perform a soft reset by pressing the reset button on the Reader.
  4. After the RESET button has been pressed, slide the POWER switch to activate the Reader device again. If the Indicator light nextto the power button on the Reader device is yellow, the unit is attempting to start up. If this is the case, allow it a few moments to complete startup.
  5. If the Reader is still not charging up properly, connect the Reader to computer or AC Adaptorand then press the reset button.
  6. Disconnect the Reader device from the computer (if applicable) and then slide the POWER switch to activate the Readerdevice. Check if the Indicator light next to the powerswitch on the Reader device is yellow (indicating it is turning on) and if the unit is responding.
    If the unit isstill frozen, connect it again to the computer or AC adapter and while connected,check if the Indicator light next to the power switch on the Reader device is red. If this light is red , allow the Reader device tocharge for one hour sothere is sufficient charge for troubleshooting.


    If the issue persists, perform a hard reset to resolve the issue. Please follow the steps to perform a hard reset:

    shajanrs_3.jpg


    Under certain circumstances, moisture condensation can occur. Moisture condensation can becaused by moving the Reader device between temperature extremes or if theReader device has come in direct contact with moisture. If you suspect moistureas the cause, allow the Reader device to sit for a few hours before attempting to turn it back on.








Reader is frozen, PRS650 frozen, image stayed in PRS650, Help to reset PRS 650. RESET PRS650. how to reset PRS-650. Hard reset PRS650. How to perform a hard reset for PRS 650. PRS650 freeze, PRS-650 frozen.PRS-650 is not charging, does not turn on PRS 650, PRS650 is not turning ON. PRS-650 does not charge.

on Jan 12, 2011 | Home Theater Systems

Tip

If after replacing the lamp it did not light up.


Hi,Sometimes after replacing the lamp on their DLP or LCD people still keep getting the red lamp indicator or simply it doesn't light up.Most of the time people forget to close the door cover of the lamp area.There's a switch that's pressed when the door is full shut,if it's not pressed it will not let the tv light up for safety reasons.Another reason why it doesn't light up or keep getting the lamp indicator is because it needs to be reset it,for most tv's what works is to unplug it wait 5 min and plug it back again.For some Mitsubishi models they have a reset button you can press and that will do the work.Other brands have reset procedures like holding the menu button while pressing volume button etc.After you've done this and still doesn't light up you might be experimenting the most common failures like the ballast which is the board that powers the lamp.When the ballast is to weak to power the lamp it might light it up for some minutes and then will shut it off.The procedure and cost to replace it is easy and low in repair cost.This is something you can do your self,most instructions are on youtube.

on Mar 23, 2010 | Home Theater Systems

1 Answer

Red flash light blinking.


That's a short circuit indicator. If you have some electronic skills u can repair it, else send it to a repair shop.

Apr 20, 2014 | Marantz PM6004 Integrated Amplifier

1 Answer

When DVD is plugged in the red stand-by light comes on, but when the power button is pushed the stand-by light goes out and the DVD will not come on. I have attempted to reset by holding power button down...


Hi Erickson,

First of all, thank you for posting your question here at Fixya.

I'm assuming here that your unit is Sharp BD-MPC41U.

The symptoms you've mentioned indicated that the power supply board of your unit gone to protection mode that's why the LED automatically shuts off. It will encountered once the feedback circuitry sensed malfunction and immediately turned off the unit to avoid further damaged.
To resolve the issue, you have to replaced the power supply board, part number RUNTKA699WJN0. I saw it in stock at this LINK or obtain it from your local Sharp service centers.

Also, don't forget to check if your unit is under warranty period (1 year), if so, avail it because the manufacturer will fix it for free. Opening the top cover will void the warranty.

Please let me know if you need further assistance.

Hope I helped you!

Have a great Holidays!!!

Ratings and feedback are highly appreciated.

Jdvillanueva

Dec 25, 2011 | Sharp BDMPC41U Theater System

1 Answer

RCA tv need the remote codes all of them in one answer


Hello
Four digit universal remote codes for RCA TV are:
0031 0004 0048 0054 0094 0100 0102 0107 0129 0191 0005 0009 0000 0162 0163 0342 0003 0015 0022 0096 0113 0125 0179 0187 0188
Three digit codes are:
000/ 003/ 004/ 005/ 007/ 009/ 011/ 048/ 078/ 082/ 083/ 094/ 096/ 098/ 099/ 101/ 102/ 103/ 107/ 113/ 129/ 133/ 167/ 179/ 181/ 187/ 188/ 194
Direct Code Entry
  1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
  3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
  4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.
Code Search method

If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.
  1. Manually turn on the device (TV, VCR, etc.) to be controlled.
  2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
  3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
  4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
  5. Press and release MUTE to install the code. The indicator light goes off.
Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search
OK.

Oct 08, 2011 | Home Theater Systems

1 Answer

We have problem Code:2,114,0 for Canon M140 scanner


Normally this Error Message Code is associated with Low/No Ink.
Try printing from the Scanner and, if it is a Low/No Ink problem, this will show up on your PC/Laptop as a Low/No Ink Message.
Solution - Try replacing the Ink Cartridge. This should normally fix this sort of problem. If it doesn't, then something more sinister might be behind the message. If this is the case, then Canon will have a fix for you.
Please let me know how you get on.
Good Luck

Mar 24, 2011 | Home Theater Systems

1 Answer

Sony DAV-C770 Red Light Flashing but nothing is on!


power supply or power amplifire unit problem.give it to repair proffesional.

nuwan.

Jan 19, 2009 | Sony DAV-C770 System

6 Answers

FAC-FC7 DVD player is locked and the Standby indicator flashes


I had the same problem and searched FIX and found a solution for a Phillips DVD player that worked on my Sony DAV-FC7 dvd player. Someone posted that they called their Phillips Tech Service and was told to (a) unplug the dvd unit from the wall and wait 20 seconds,then (b) press the standby+plug the unit back into the wall at the same time and hold for 10 seconds. I did this for my Sony DAV-FC7 which would not power on nor eject (just red light on). IT WORKED!! after doing these steps, my SONY powered on and the rented DVD ejected. The dvd palyer works again. Thanks fellow FIXYA "posters".

Nov 12, 2007 | Sony DAV-FC7 System

2 Answers

Emerson AV101 System


I'm in the same boat... happened once before, then came back to life. Now it's back to a red standby light and no ejecting tray

Mar 04, 2007 | Emerson AV101 System

Not finding what you are looking for?
Yahoo YHT-630 System Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yahoo Home Theater Systems Experts

micky dee

Level 3 Expert

2620 Answers

Kolbrun...

Level 3 Expert

1174 Answers

 Larry
Larry

Level 2 Expert

115 Answers

Are you a Yahoo Home Theater System Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...