Question about Remote Controls

1 Answer

INSTRUCTIONS NEEDED FOR THE SHARPER IMAGE - JUMBO UNIVERSAL REMOTE

I need to program my jumbo universal remote " THE SHARPER IMAGE" but can't find the instructions needed to use the proper code for a Sanyo TV. Help! I have a Sharper Image Universal Remote Control and can't find the code for the Dish Network DVR!! HELP!!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 4 Answers

Hello kls1996... programming your remote is rather easy. The easiest way (thanks to The Sharper Image Jumbo Remote being a LEARNING SMART remote) is to do the following:

1 - Point the head of your Sharper Image remote at the head of your Sanyo TV remote (nose to nose so the clear bulbs on each remote are facing each other).

2 - Press the "TV" button on your Sharper Image remote (located in the upper left-hand corner).

3 - Hold the "LEARN" button on your Sharper Image remote (located in the left edge under the volume buttons) until the red light flashes.

4 - Press the key on your Sharper Image remote (e.g. Volume Up or +VOL)... the red light will go solid (indicating that it is waiting for a signal from the other (in your case Sanyo) remote.

5 - Press the key on your other remote (in your case the Sanyo remote) that you want programmed in your new Sharper Image remote... the red light will flash rapidly again.

6 - Repeat step #4 until you have programmed each key.

7 - When done... press the "LEARN" key on your Sharper Image remote. Your Sharper Image remote should be programmed to operate your device (in this case, your Sanyo TV).

NOTE: You can program other devices such as your VCR, DVD, VHS, SAT, CABLE, etc. and not just one device.

Posted on Jan 16, 2009

  • Ellen Wilson Nov 11, 2012

    well my sharper image jumbo remote doesnt have a learn or code search button so now what

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The sharper image jumbo universal remote jvc tv


I found that this website should have all the codes and instructions for most remotes
http://www.xdiv.com/remotes/

Jan 04, 2010 | Remote Controls

Tip

Sharper Image Jumbo Remote Manual


Sharper Image Jumbo Universal Remote Control Manual

7ccad88.gif


Have you misplaced your Sharper Image Jumbo Universal Remote Control Owners Manual?

Would you like a digital, searchable, pdf version of the Sharper Image Jumbo Universal Remote Control Users Guide?

Follow this link to download a pdf version of the operations manual.

I hope that helps.

on Apr 30, 2010 | Remote Controls

1 Answer

I need codes for sharper image jumbo remote control


If you go to a website called www.mscustomercare.com. Scroll down to the bottom of the page click on The Sharper Image Universal Jumbo Remote then click download. The manual has the instructions and codes for your stuff. Good Luck.

Aug 30, 2009 | Emerson Remote Controls

1 Answer

Programming


i need codes to jumbo sharper image universal remote

Jan 27, 2009 | One For All URC-9910 LCD Remote Control

19 Answers

INSTRUCTIONS NEEDED FOR THE SHARPER IMAGE - JUMBO UNIVERSAL REMOTE


The "auto" mode isn't quite presented correctly in the documentation or posts I've seen...after MUCH trial and error (and about 3 hous) I've been able to set-up ANY infrared device, either by "auto" or learn. (Although maybe not "fully".)

AUTO Method

1. Press & Hold (about 3 sec.) the [DEVICE] button on the JUMBO Remote....llight will stay solid.
2. Now just press the [POWER] button (only) ONCE while pointing at the device...it will start sending codes approximately every second. (Don't keep pressing the power button as instructions indicate.)
3. TIMING IS EVERYTHING HERE. (It may take 5 minutes to find your devices code.)
4. AS SOON AS the power goes off...press the [ENTER] button on the JUNBO Remote.
5. Now pressing the [POWER] button should power up/down the device.

---- any buttons not programmed will have to be handled using the LEARN method ---

LEARN Method

1. Press & Hold (about 3 sec.) the [DEVICE] button on the JUMBO Remote....it'll stay solid.
2. Press the [LEARN] button on the JUMBO Remote. (light will immediately blink rapidly.)
3. Now Press the {NEEDED} button to program. (light will stay solid)
4. Now (1 to 2 inches away) have the ORIGINAL Remote pointed at the JUMBO Remote and press the {DESIRED} button on the ORIGINAL Remote.
5. It blinks rapidly while sending...then a slower steady blink once "LEARNED" correctly.

*** Not all buttons work properly with the "LEARN method". Some you will need to "associate" with an alternate button on the JUMBO Remote. ***

I sincerely hopes this helps anyone & everyone.

Feb 09, 2008 | Remote Controls

4 Answers

Sharper Image Jumbo Universal Remote


i just pirchased a Sharper Image Jumbo universal Remote but i can't find a code for the Pioneer DVR 541H is DVD recorder. Does anyone have this code or  a suggestion?

Jan 10, 2008 | Remote Controls

12 Answers

Jumbo Universal TV Remote (Sharper Image-Innovage)


sharper image jumbo remote can't get it to program my philips/magnavox tv.

Dec 25, 2007 | One For All URC-9910 LCD Remote Control

Not finding what you are looking for?
Remote Controls Logo

Related Topics:

3,047 people viewed this question

Ask a Question

Usually answered in minutes!

Top Remote Controls Experts

The Knight
The Knight

Level 3 Expert

68323 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Cindy Wells

Level 3 Expert

4758 Answers

Are you a Remote Control Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...