Question about Zyxel Prestige 334 Router

1 Answer

Zyxel nbg334w router configuration

When i connect my ethernet cable from bt hub to my nbg334w router then a ethernet cable to my laptop it says in manual to access an internet browser an type http://192.168.1.1 ,thing is when i do this its says web page not found???? now i need to find this page to carry on wiv step 3 in the instruction manuel ! all my settings like i.p addresss etc is set to automatic ! am new to this so can any1 out there help me? many thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 50 Answers

Hi

To configure the wireless router it is recommended the it is connected directly to router.
Please follow these steps to fix your issue

1. Reset the router using reset button on the back of the NBG334W router
2. Configure or change the laptop ehternet adaptor setting to "Obtain IP address automatically.
3 connect laptop and router using ethernet cable. check the ip address using ipconfig command in DOS prompt. If IP address is 0.0.0.0 or 169.X..X..X run command
ipconfig /release
ipconfig/ renew

best way restart the computer

4. if you still have issue in getting ip address double check ethernet cable and try reseting the router again.

5. Still problem persist install new firmware on the router. you can download router firmware from
http://www.zyxel.com/web/support_download_list.php?indexflag=20040906164737&ModelIndexflags=0,420070320142921

Please vote if this information is helpful in resolving your issue



Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Zyxel P660HW-T1 v2 and when trying to use laptop wirelessly, the internet connection keeps dropping. While connected to the router by ethernet cable, internet is fine. All was working fine until...


For that you need to change wireless channel type in router. You can also configure it with below method.
Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Then click on wireless->wireless channel type to 3 or 6 or 11 then save settings and restart router. . Let me know if you need further assistance. Thanks for using FixYa.

Jun 22, 2011 | Zyxel Prestige 660HW Wireless Router...

2 Answers

I am trying to configure my new NBG4115 3G router connexion, but when I try to connect to the Zyxel setup screen via http://192.168.1.1 the Tilgin home screen appears. My present router here in our home is...


Either your web-browser has "cached" the web-page previously delivered by the TILGIN,
or your computer is still connected to the TILGIN.

In the former case, "reload" the web-page.
In the latter case, turn off the TILGIN router, and try again to connect to the ZYXEL router.
Also, check that your network-cables are correctly connected to one of the LAN ports on the ZYXEL router.

May 12, 2011 | Zyxel NBG-415N Router

1 Answer

Ethernet to router connectivity issue


The correct way to do the connection is by plugging the Desktop to one of the Ethernet ports and any wireless device over the wireless network.


Dec 01, 2009 | Zyxel P660HW-D1 Router

1 Answer

I have a BT 2-wire hub with networked printer.


First thing, Does your printer have a wireless facility built in? If not it has to be connected to the hub with ethernet.
Normally setting up a wireless printer involves using cables until the set-up is complete. It's nothing to do with the router but all to do with the printer.
Best thing is to go through the manual.

Oct 14, 2009 | 2wire (1000-400108-001) Router

4 Answers

I wish to restore the factory settings for my Zyxel router


Greetings my name is Mark and I will be glad to assist you.
To restor the factory default first unplug the router then hold the switch down and while depressed plug the unit in and keep holding the button down for fifteen seconds then release the button and count to fifteen again, once more depress the button for fifteen seconds and let go let the router reboot for one minute. Unplug the router for thirty seconds then plug the router in and you should be restored. Let me know if that helps.
Be mucho blessed,
mark

Dec 31, 2008 | Zyxel Prestige 334 Router

1 Answer

Configuring nbg334w router


To configure the wireless router it is recommended the it is connected directly to router.
Please follow these steps to fix your issue

1. Reset the router using reset button on the back of the NBG334W router
2. Configure or change the laptop ehternet adaptor setting to "Obtain IP address automatically.
3 connect laptop and router using ethernet cable. check the ip address using ipconfig command in DOS prompt. If IP address is 0.0.0.0 or 169.X..X..X run command
ipconfig /release
ipconfig/ renew

best way restart the computer

4. if you still have issue in getting ip address double check ethernet cable and try reseting the router again.

5. Still problem persist install new firmware on the router. you can download router firmware from
http://www.zyxel.com/web/support_download_list.php?indexflag=20040906164737&ModelIndexflags=0,420070320142921

Please vote if this information is helpful in resolving your issue

Dec 27, 2008 | Zyxel Prestige 334 Router

1 Answer

Wireless connection fine but internet connection impossible


if you only have usb connection in your modem, internet on the zyxel router will not work since it's using ethernet connection. in order for your zyxel device to work with tiscali, you will need a cable/dsl router that has ethernet connection as well. you can contact tiscali if they can provide you with that kind of modem.

hope this'll help you

ciao

Nov 10, 2008 | Zyxel Prestige 334 Router

4 Answers

Installing wireless router


um is it compatible with vista and/or upgradable?

Jan 15, 2008 | Zyxel Prestige P-330W Wireless Router...

4 Answers

Trying to configure zyxel nbg334w router


If the router will not connect to the internet, you will need to create the PPPOE internet connection with the username and password that your ISP provided. BPCS

Dec 28, 2007 | Zyxel Prestige 334 Router

Not finding what you are looking for?
Zyxel Prestige 334 Router Logo

1,143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zyxel Routers Experts

Courtney Lomax
Courtney Lomax

Level 2 Expert

83 Answers

Justin
Justin

Level 3 Expert

2072 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Are you a Zyxel Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...