Question about HP OfficeJet 6210 All-In-One InkJet Printer

1 Answer

Error code 0xc0620004 411:lib_micci2.c

All lights are flashing on the front of the printer and the
error code above is flashing in the window

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

There is not a lot of info around concerning this error message.

One similar problem on fixya:

Click here


If it doesn't work you should try to contact HP on their

HP support site

Hope that helps

Critter






Posted on Dec 27, 2008

1 Suggested Answer

  • 366 Answers

SOURCE: error code 0xc0620004 411:lib-micci2.c diplayed

Hi

This is a somewhat common error on HP all-in-one printers. Try the following, per HP: Give it a shot and see what happens...

The issue as this issue may occur because of ink system failure of the All-in-one.

Please follow the below given instructions to resolve the issue.

Please remove the All-in-One Printer from the Power Surge Protector and plug it directly into a wall Power outlet, as the surge protector may not provide enough power to printer.

Please perform the step given below to power cycle the unit after removing the print cartridges from the printer:

1. Verify that the unit is switched on. Unplug the all-in-one from power and disconnect the USB cable from the computer.
2. Wait 30 seconds.
3. Plug in the power only
4. Repeat steps 2-3 two more times.
5. On the third time after plugging the unit into power, reconnect the USB cable from the all-in-one to your computer.

Clean the cartridges by following the below given instructions:

Using a clean, dry lint-free cloth (a coffee filter works well), wipe the cartridge contacts, from the top to the bottom. The contact area of the cartridge should be rubbed briskly to remove the waxy lubricant material from the gold contacts. The contacts inside the printer may also require cleaning. Using a clean, dry, lint-free cloth, gently wipe the contacts, from the top to the bottom.

Also clean the cartridge carriage rod with a soft lint free cloth to resolve the issue.

Even if the issue persists, then try resetting the All-in-one to factory defaults.

Reset the All-in-One to the factory default settings by using these instructions:
1. Unplug the power cable from printer when the printer is powered on and wait for 20 seconds.
2. Then, press and hold # XXX 6 while plugging in the power cord.
Continue holding until it displays Semi Full Reset message in the front panel of the All-in-One.

Note:
A semi-full reset will do the following:
The user settings to the factory defaults, Language and country settings on some models, Fax logs, Fax headers, Fax speed dial information.


Also, check to make sure the flat cable to the print head is seated properly (if you know what this is)

Posted on Jul 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix OXC1AB0003 error on the P PhotoSmart 2575


Remove the cartridges and do a full reset without them in by removing the wall socket and re-plugging.

More information has been answered in another thread.
Error oxc1ab0003730 Lib micci2 tango

Apr 07, 2015 | HP PhotoSmart 2575 / 2575v / 2575xi InkJet...

1 Answer

Error code 0xc0620004 411:lib-micci2.c diplayed


Hi

This is a somewhat common error on HP all-in-one printers. Try the following, per HP: Give it a shot and see what happens...

The issue as this issue may occur because of ink system failure of the All-in-one.

Please follow the below given instructions to resolve the issue.

Please remove the All-in-One Printer from the Power Surge Protector and plug it directly into a wall Power outlet, as the surge protector may not provide enough power to printer.

Please perform the step given below to power cycle the unit after removing the print cartridges from the printer:

1. Verify that the unit is switched on. Unplug the all-in-one from power and disconnect the USB cable from the computer.
2. Wait 30 seconds.
3. Plug in the power only
4. Repeat steps 2-3 two more times.
5. On the third time after plugging the unit into power, reconnect the USB cable from the all-in-one to your computer.

Clean the cartridges by following the below given instructions:

Using a clean, dry lint-free cloth (a coffee filter works well), wipe the cartridge contacts, from the top to the bottom. The contact area of the cartridge should be rubbed briskly to remove the waxy lubricant material from the gold contacts. The contacts inside the printer may also require cleaning. Using a clean, dry, lint-free cloth, gently wipe the contacts, from the top to the bottom.

Also clean the cartridge carriage rod with a soft lint free cloth to resolve the issue.

Even if the issue persists, then try resetting the All-in-one to factory defaults.

Reset the All-in-One to the factory default settings by using these instructions:
1. Unplug the power cable from printer when the printer is powered on and wait for 20 seconds.
2. Then, press and hold # XXX 6 while plugging in the power cord.
Continue holding until it displays Semi Full Reset message in the front panel of the All-in-One.

Note:
A semi-full reset will do the following:
The user settings to the factory defaults, Language and country settings on some models, Fax logs, Fax headers, Fax speed dial information.


Also, check to make sure the flat cable to the print head is seated properly (if you know what this is)

Jul 23, 2010 | HP PSC 2355 All-In-One InkJet Printer

1 Answer

What is an error 1-2070 mean?


Check to see if the required files are present:
  • Go to C:\WINDOWS\system32\kodak. Check for 2 folders "kds_aio5000(for AiO 5000 series printers) and kds_aioesp(for ESP series)
  • Depending on printer model, open kds_aio5000 or kds_aioesp.
    • For kds_espaio it should only have the lib folder. It doesn't have the ekaiowia.dll
  • Inside the lib folder it should have cct.ekpgct, hippo.dll. Both for kds_aio5000 and kds_aioesp.
  • If hippo.dll is missing then try the following:
Option 1: 1. Go to C:\Documents and Settings\All Users\Application Data\Kodak\EasyShareSetup\printer\scanner 2. Right click on aioscnnr.msi2_bing.gif and choose uninstall once this is finished reinstall it by double clicking on the same msi file. 3. Check to see if the scanner files are now present (see above) if not then go to Option 2 Option 2: 1. Insert the Home AiO CD. Go to CD rom2_bing.gif drive\printer\scanner 2. Right click on aioscnnr.msi and choose uninstall once this is finished reinstall it by double clicking on the same msi file. 3. Check to see if the scanner files are now present (see above) if not then go to Option 3 Option 3: (manual installation) 1. Go to C:\Documents and Settings\All Users\Application Data\Kodak\EasyShareSetup\printer\scanner or on CDROM drive2_bing.gif ..\printer\scanner 2. Open the aioscnnr.cab file then look for the missing file(files needed: cct.ekpgct, hippo.dll, and ekaiowia.dll) Extract the files anywhere on to the computer (Desktop is preferable). 3. Copy the cct.ekpgct, and hippo.dll to C:\WINDOWS\system32\kodak\kds_aio5000\lib 4. Copy the ekaiowia.dll to C:\WINDOWS\system32\kodak\kds_aio5000

Apr 30, 2010 | Kodak EASYSHARE 5300 All-In-One InkJet...

1 Answer

My samsung ml-1610 series printer's software is installed but the printer is not installed


my oj 7310 all in one is give me error mesege 0xc0620004 411:lib-micci2.c

Nov 03, 2009 | Samsung ML 1610 Laser Printer

1 Answer

I keep getting error 1-2070


Resolution
Check to see if the required files are present:
  • Go to C:\WINDOWS\system32\kodak. Check for 2 folders "kds_aio5000(for AiO 5000 series printers) and kds_aioesp(for ESP series)
  • Depending on printer model, open kds_aio5000 or kds_aioesp.
    • For kds_espaio it should only have the lib folder. It doesn't have the ekaiowia.dll
  • Inside the lib folder it should have cct.ekpgct, hippo.dll. Both for kds_aio5000 and kds_aioesp.
  • If hippo.dll is missing then try the following:
Option 1: 1. Go to C:\Documents and Settings\All Users\Application Data\Kodak\EasyShareSetup\printer\scanner 2. Right click on aioscnnr.msi and choose uninstall once this is finished reinstall it by double clicking on the same msi file. 3. Check to see if the scanner files are now present (see above) if not then go to Option 2 Option 2: 1. Insert the Home AiO CD. Go to CD rom drive\printer\scanner 2. Right click on aioscnnr.msi and choose uninstall once this is finished reinstall it by double clicking on the same msi file. 3. Check to see if the scanner files are now present (see above) if not then go to Option 3 Option 3: (manual installation) 1. Go to C:\Documents and Settings\All Users\Application Data\Kodak\EasyShareSetup\printer\scanner or on CDROM drive ..\printer\scanner 2. Open the aioscnnr.cab file then look for the missing file(files needed: cct.ekpgct, hippo.dll, and ekaiowia.dll) Extract the files anywhere on to the computer (Desktop is preferable). 3. Copy the cct.ekpgct, and hippo.dll to C:\WINDOWS\system32\kodak\kds_aio5000\lib 4. Copy the ekaiowia.dll to C:\WINDOWS\system32\kodak\kds_aio5000

Apr 12, 2009 | Kodak ESP 5 Printer

1 Answer

Hp 2355 all in one error message


Hi, 

open the rear access door and clean the rollers with a cloth, dam it with little water and unplug the machine and press and hold the ON button for 1 min and release the button and plug in the power cord, it should resolve the issue.

Regards,  raj_p5983 

Jan 21, 2009 | HP OfficeJet 7310 All-In-One InkJet...

2 Answers

Hp 2355 all in one error message


reset to factory defaults, also check the whole printer for paper jams. A paper jam can often casue smaller pieces to get stuck in gears or rollers. The message about opening and closing the lid is how the printer knows you went in to check it and closeing it triggers it to try again. If thers still a jam it will keep giving the message. The fist jam was caused by something, check and make sure there isnt any pieces of plastic broken off inside. If it has a rear access panel, check there also.

Feb 16, 2008 | HP PSC 2355 All-In-One InkJet Printer

3 Answers

Unable to init error message and and machine error 4f


i can not print any documents it keeps coming up as Init unable 4f please help ?

Sep 27, 2007 | Brother MFC 210C All-In-One InkJet Printer

2 Answers

Error: 0x07a74dd61959:lib-barracu


Its a Fimware Error.
Try a Hardware Reset.
-Switch the Printer on
-unplug the powerkable
-press "#" and "6" and plug in the Powerkable.
when the Display shows Initialising or Semi-Full-Reset. release the "#" and the"6".

sometime this is working

Jul 14, 2007 | HP OfficeJet 6210 All-In-One InkJet...

Not finding what you are looking for?
HP OfficeJet 6210 All-In-One InkJet Printer Logo

588 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Printers & Copiers Experts

kakima

Level 3 Expert

96396 Answers

k24674

Level 3 Expert

7987 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a HP Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...