Question about Amana PTH123B25AJ Heat Pump Air Conditioner

1 Answer

Ptac i recieved a power cord replacement as per recall. did as instructions said. I did turn off master off/on switch on pc board. after i was finished I turned switch on/ closed cover and plugged in cord. the panel lit up and i pushed HEAT. cold air blew for abt 30 seconds and stopped and a clicking noise began. I unplugged cord and started looking for answers. can u advise? its less then a year old.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 142 Answers

You need a new control board. The relays go out on these. If your unit is less than a year old then you should still be under warranty. Unless you did not send in the warranty card, then the company only warrants the unit for 1 year after the mfg. date. You will need to provide the serial and part number to find out from Amana. The new control boards are much better by the way, and worse come to worse, they are only $130. Please let me know if this has helped in any way.

Posted on Feb 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My amana ptac is not heating....the code "np" is displayed....how do I correct this...we just installed the unit and know little about operation. Thanks


I don't see this error code in the manual. I do see nP as an error code for Window Switch lockout. I just had this happen to me and they had me reset the control board.

Remove case, flick master switch to OFF for 10 seconds. Press Heat/Cool same time turn switch back on HOLD until off light comes on.

You should be fixed. Just had to do this for my unit. I was playing around with the settings and turned on the window switch option by accident.

Feb 02, 2013 | Amana In Wall Install Kit For Digismart...

2 Answers

I have a Samsung LN52A650A LCD TV that 3 years old. Today when I go to turn it on it just clicks and does not turn on. The clicking wont stop...it clicks about once per second. I have to unplug the TV to...


The tv power supply board have dead components parts call capacitors most likely.U have all the tools and understanding basic electronic also can do basic soldering too?The tv power supply board that the board where the power a/c cord plug into it.Take the tv aparts and check the tv power supply board carefully for dying and dead capacitors parts.These capacitors parts are alway bulges up or puffing up on to it tops.Must replaced all these dying capacitors parts are bulging up ur puffing up on to it tops.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole new refurbish power supply board for the replacement.

May 11, 2011 | Samsung LN52A650A LCD TV

1 Answer

I just replaced the lamp, but the projector won't power up. It has 2 solid red lights


To resolve the issue, follow these steps:
1. Turn off the master power switch, disconnect the power cord, and then wait a short time.
2. Reconnect the power cord, and then turn on the master power switch. 3. If the previous steps don’t resolve the issue, the lamp might be at the end of its life. (double check that you get a good one lamp, and that are installed correctly)
4. If your projector still doesn’t turn on, turn off the master power switch, disconnect the power cord, and then contact your local repair shop for Fix the Board on the prjector

Mar 11, 2010 | Mitsubishi HC3000U Multimedia Projector

1 Answer

Amana ptac


you have the white wire on the wrong terminal put it on the same terminal as the red wire on the capacitor and you should be fine,

Dec 27, 2008 | Amana PTH123B25AJ Heat Pump Air...

1 Answer

PTC153B50AM REPLACED POWER CORD ON RECALL


First off, you need to unplug power from the unit before handling anything on it, not just the master switch on the control board. There is still live power being fed to the unit while it is plugged in!
Now, the clicking sound you are hearing is a faulty relay on the control board. You have to replace the control board. The new ones are available from Amana/Goodman Mfg.. You will find, assuming you have more of these, your other units are going to start doing the same thing. It will be the same problem. When they send out the new control board, make sure you program the board. They no longer come pre programmed. It is actually a huge improvement on the older control board upgrades. Hope this helps, I have 140 of these in my hotel, I know them all too well. Let me know if you have any other questions and please rate this as a fix ya.

Dec 25, 2008 | Amana PTH123B25AJ Heat Pump Air...

1 Answer

System turns on however hard drive will not cycle nor will mouse or key board activate


Turn power off and unplug power from computer.
Unplug printers,backup drives and speakers.
Open case and unplug power supply from the board.
plug power cord back in press the power button.
Of course nothing will happen.
unplug power cord again.
plug power supply back into the board.
plug power cord backup and press power switch.
If nothing happens unplug power cord again.
pull out your memory sticks and plug cord back in and press power button.
Of course not much will happen.
But really something is happening to your computer so continue.
Pull power cord and replace memory sticks.
replace power cord and press power switch.
Continue this pulling out pci cards one at a time until you find out what the problem might be.
Try different keyboards and mice too.
Good Luck

Oct 27, 2008 | Intel Computers & Internet

2 Answers

PTAC UNIT QUIT WORKING


If you have a clamp tester, operate the unit with the clamp tester and check the current reading. If the current reading is normal but the reset button is tipped then there is something wrong withe power plug reset button. But if the current reading is higher than the name plate rating then there is something wrong with the unit.

Mar 09, 2008 | GE Zoneline AZ38H12DAD Split System Air...

3 Answers

TRANE PTAC


You need to replace your control board, but if you are can repair it by your self you can change the relay that supply the fan and condenser.

Nov 15, 2007 | Heating & Cooling

3 Answers

Ptac fan keeps blowing


Try setting the fan control to "AUTO" this will cause it to cut out with the compressor.

May 02, 2007 | Amana PTH123B25AJ Heat Pump Air...

Not finding what you are looking for?
Amana PTH123B25AJ Heat Pump Air Conditioner Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Donni Steen

Level 3 Expert

659 Answers

Bill Long

Level 3 Expert

587 Answers

Are you an Amana Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...